| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/sun4i: dsi: Prevent underflow when computing packet sizes
Currently, the packet overhead is subtracted using unsigned arithmetic.
With a short sync pulse, this could underflow and wrap around to near
the maximal u16 value. Fix this by using signed subtraction. The call to
max() will correctly handle any negative numbers that are produced.
Apply the same fix to the other timings, even though those subtractions
are less likely to underflow. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: Fix mcam entry resource leak
The teardown sequence in FLR handler returns if no NIX LF
is attached to PF/VF because it indicates that graceful
shutdown of resources already happened. But there is a
chance of all allocated MCAM entries not being freed by
PF/VF. Hence free mcam entries even in case of detached LF. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: fix stuck flows on cleanup due to pending work
To clear the flow table on flow table free, the following sequence
normally happens in order:
1) gc_step work is stopped to disable any further stats/del requests.
2) All flow table entries are set to teardown state.
3) Run gc_step which will queue HW del work for each flow table entry.
4) Waiting for the above del work to finish (flush).
5) Run gc_step again, deleting all entries from the flow table.
6) Flow table is freed.
But if a flow table entry already has pending HW stats or HW add work
step 3 will not queue HW del work (it will be skipped), step 4 will wait
for the pending add/stats to finish, and step 5 will queue HW del work
which might execute after freeing of the flow table.
To fix the above, this patch flushes the pending work, then it sets the
teardown flag to all flows in the flowtable and it forces a garbage
collector run to queue work to remove the flows from hardware, then it
flushes this new pending work and (finally) it forces another garbage
collector run to remove the entry from the software flowtable.
Stack trace:
[47773.882335] BUG: KASAN: use-after-free in down_read+0x99/0x460
[47773.883634] Write of size 8 at addr ffff888103b45aa8 by task kworker/u20:6/543704
[47773.885634] CPU: 3 PID: 543704 Comm: kworker/u20:6 Not tainted 5.12.0-rc7+ #2
[47773.886745] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009)
[47773.888438] Workqueue: nf_ft_offload_del flow_offload_work_handler [nf_flow_table]
[47773.889727] Call Trace:
[47773.890214] dump_stack+0xbb/0x107
[47773.890818] print_address_description.constprop.0+0x18/0x140
[47773.892990] kasan_report.cold+0x7c/0xd8
[47773.894459] kasan_check_range+0x145/0x1a0
[47773.895174] down_read+0x99/0x460
[47773.899706] nf_flow_offload_tuple+0x24f/0x3c0 [nf_flow_table]
[47773.907137] flow_offload_work_handler+0x72d/0xbe0 [nf_flow_table]
[47773.913372] process_one_work+0x8ac/0x14e0
[47773.921325]
[47773.921325] Allocated by task 592159:
[47773.922031] kasan_save_stack+0x1b/0x40
[47773.922730] __kasan_kmalloc+0x7a/0x90
[47773.923411] tcf_ct_flow_table_get+0x3cb/0x1230 [act_ct]
[47773.924363] tcf_ct_init+0x71c/0x1156 [act_ct]
[47773.925207] tcf_action_init_1+0x45b/0x700
[47773.925987] tcf_action_init+0x453/0x6b0
[47773.926692] tcf_exts_validate+0x3d0/0x600
[47773.927419] fl_change+0x757/0x4a51 [cls_flower]
[47773.928227] tc_new_tfilter+0x89a/0x2070
[47773.936652]
[47773.936652] Freed by task 543704:
[47773.937303] kasan_save_stack+0x1b/0x40
[47773.938039] kasan_set_track+0x1c/0x30
[47773.938731] kasan_set_free_info+0x20/0x30
[47773.939467] __kasan_slab_free+0xe7/0x120
[47773.940194] slab_free_freelist_hook+0x86/0x190
[47773.941038] kfree+0xce/0x3a0
[47773.941644] tcf_ct_flow_table_cleanup_work
Original patch description and stack trace by Paul Blakey. |
| In the Linux kernel, the following vulnerability has been resolved:
BPF: Fix potential bad pointer dereference in bpf_sys_bpf()
The bpf_sys_bpf() helper function allows an eBPF program to load another
eBPF program from within the kernel. In this case the argument union
bpf_attr pointer (as well as the insns and license pointers inside) is a
kernel address instead of a userspace address (which is the case of a
usual bpf() syscall). To make the memory copying process in the syscall
work in both cases, bpfptr_t was introduced to wrap around the pointer
and distinguish its origin. Specifically, when copying memory contents
from a bpfptr_t, a copy_from_user() is performed in case of a userspace
address and a memcpy() is performed for a kernel address.
This can lead to problems because the in-kernel pointer is never checked
for validity. The problem happens when an eBPF syscall program tries to
call bpf_sys_bpf() to load a program but provides a bad insns pointer --
say 0xdeadbeef -- in the bpf_attr union. The helper calls __sys_bpf()
which would then call bpf_prog_load() to load the program.
bpf_prog_load() is responsible for copying the eBPF instructions to the
newly allocated memory for the program; it creates a kernel bpfptr_t for
insns and invokes copy_from_bpfptr(). Internally, all bpfptr_t
operations are backed by the corresponding sockptr_t operations, which
performs direct memcpy() on kernel pointers for copy_from/strncpy_from
operations. Therefore, the code is always happy to dereference the bad
pointer to trigger a un-handle-able page fault and in turn an oops.
However, this is not supposed to happen because at that point the eBPF
program is already verified and should not cause a memory error.
Sample KASAN trace:
[ 25.685056][ T228] ==================================================================
[ 25.685680][ T228] BUG: KASAN: user-memory-access in copy_from_bpfptr+0x21/0x30
[ 25.686210][ T228] Read of size 80 at addr 00000000deadbeef by task poc/228
[ 25.686732][ T228]
[ 25.686893][ T228] CPU: 3 PID: 228 Comm: poc Not tainted 5.19.0-rc7 #7
[ 25.687375][ T228] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS d55cb5a 04/01/2014
[ 25.687991][ T228] Call Trace:
[ 25.688223][ T228] <TASK>
[ 25.688429][ T228] dump_stack_lvl+0x73/0x9e
[ 25.688747][ T228] print_report+0xea/0x200
[ 25.689061][ T228] ? copy_from_bpfptr+0x21/0x30
[ 25.689401][ T228] ? _printk+0x54/0x6e
[ 25.689693][ T228] ? _raw_spin_lock_irqsave+0x70/0xd0
[ 25.690071][ T228] ? copy_from_bpfptr+0x21/0x30
[ 25.690412][ T228] kasan_report+0xb5/0xe0
[ 25.690716][ T228] ? copy_from_bpfptr+0x21/0x30
[ 25.691059][ T228] kasan_check_range+0x2bd/0x2e0
[ 25.691405][ T228] ? copy_from_bpfptr+0x21/0x30
[ 25.691734][ T228] memcpy+0x25/0x60
[ 25.692000][ T228] copy_from_bpfptr+0x21/0x30
[ 25.692328][ T228] bpf_prog_load+0x604/0x9e0
[ 25.692653][ T228] ? cap_capable+0xb4/0xe0
[ 25.692956][ T228] ? security_capable+0x4f/0x70
[ 25.693324][ T228] __sys_bpf+0x3af/0x580
[ 25.693635][ T228] bpf_sys_bpf+0x45/0x240
[ 25.693937][ T228] bpf_prog_f0ec79a5a3caca46_bpf_func1+0xa2/0xbd
[ 25.694394][ T228] bpf_prog_run_pin_on_cpu+0x2f/0xb0
[ 25.694756][ T228] bpf_prog_test_run_syscall+0x146/0x1c0
[ 25.695144][ T228] bpf_prog_test_run+0x172/0x190
[ 25.695487][ T228] __sys_bpf+0x2c5/0x580
[ 25.695776][ T228] __x64_sys_bpf+0x3a/0x50
[ 25.696084][ T228] do_syscall_64+0x60/0x90
[ 25.696393][ T228] ? fpregs_assert_state_consistent+0x50/0x60
[ 25.696815][ T228] ? exit_to_user_mode_prepare+0x36/0xa0
[ 25.697202][ T228] ? syscall_exit_to_user_mode+0x20/0x40
[ 25.697586][ T228] ? do_syscall_64+0x6e/0x90
[ 25.697899][ T228] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[ 25.698312][ T228] RIP: 0033:0x7f6d543fb759
[ 25.698624][ T228] Code: 08 5b 89 e8 5d c3 66 2e 0f 1f 84 00 00 00 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
kunit: executor: Fix a memory leak on failure in kunit_filter_tests
It's possible that memory allocation for 'filtered' will fail, but for the
copy of the suite to succeed. In this case, the copy could be leaked.
Properly free 'copy' in the error case for the allocation of 'filtered'
failing.
Note that there may also have been a similar issue in
kunit_filter_subsuites, before it was removed in "kunit: flatten
kunit_suite*** to kunit_suite** in .kunit_test_suites".
This was reported by clang-analyzer via the kernel test robot, here:
https://lore.kernel.org/all/c8073b8e-7b9e-0830-4177-87c12f16349c@intel.com/
And by smatch via Dan Carpenter and the kernel test robot:
https://lore.kernel.org/all/202207101328.ASjx88yj-lkp@intel.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
USB: gadget: Fix use-after-free Read in usb_udc_uevent()
The syzbot fuzzer found a race between uevent callbacks and gadget
driver unregistration that can cause a use-after-free bug:
---------------------------------------------------------------
BUG: KASAN: use-after-free in usb_udc_uevent+0x11f/0x130
drivers/usb/gadget/udc/core.c:1732
Read of size 8 at addr ffff888078ce2050 by task udevd/2968
CPU: 1 PID: 2968 Comm: udevd Not tainted 5.19.0-rc4-next-20220628-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google
06/29/2022
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:317 [inline]
print_report.cold+0x2ba/0x719 mm/kasan/report.c:433
kasan_report+0xbe/0x1f0 mm/kasan/report.c:495
usb_udc_uevent+0x11f/0x130 drivers/usb/gadget/udc/core.c:1732
dev_uevent+0x290/0x770 drivers/base/core.c:2424
---------------------------------------------------------------
The bug occurs because usb_udc_uevent() dereferences udc->driver but
does so without acquiring the udc_lock mutex, which protects this
field. If the gadget driver is unbound from the udc concurrently with
uevent processing, the driver structure may be accessed after it has
been deallocated.
To prevent the race, we make sure that the routine holds the mutex
around the racing accesses. |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: OMAP2+: Fix refcount leak in omapdss_init_of
omapdss_find_dss_of_node() calls of_find_compatible_node() to get device
node. of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() in later error path and normal path. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: DPCM: Don't pick up BE without substream
When DPCM tries to add valid BE connections at dpcm_add_paths(), it
doesn't check whether the picked BE actually supports for the given
stream direction. Due to that, when an asymmetric BE stream is
present, it picks up wrongly and this may result in a NULL dereference
at a later point where the code assumes the existence of a
corresponding BE substream.
This patch adds the check for the presence of the substream for the
target BE for avoiding the problem above.
Note that we have already some fix for non-existing BE substream at
commit 6246f283d5e0 ("ASoC: dpcm: skip missing substream while
applying symmetry"). But the code path we've hit recently is rather
happening before the previous fix. So this patch tries to fix at
picking up a BE instead of parsing BE lists. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: light: cm3605: Fix an error handling path in cm3605_probe()
The commit in Fixes also introduced a new error handling path which should
goto the existing error handling path.
Otherwise some resources leak. |
| In the Linux kernel, the following vulnerability has been resolved:
iavf: Fix adminq error handling
iavf_alloc_asq_bufs/iavf_alloc_arq_bufs allocates with dma_alloc_coherent
memory for VF mailbox.
Free DMA regions for both ASQ and ARQ in case error happens during
configuration of ASQ/ARQ registers.
Without this change it is possible to see when unloading interface:
74626.583369: dma_debug_device_change: device driver has pending DMA allocations while released from device [count=32]
One of leaked entries details: [device address=0x0000000b27ff9000] [size=4096 bytes] [mapped with DMA_BIDIRECTIONAL] [mapped as coherent] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/hugetlb: avoid corrupting page->mapping in hugetlb_mcopy_atomic_pte
In MCOPY_ATOMIC_CONTINUE case with a non-shared VMA, pages in the page
cache are installed in the ptes. But hugepage_add_new_anon_rmap is called
for them mistakenly because they're not vm_shared. This will corrupt the
page->mapping used by page cache code. |
| In the Linux kernel, the following vulnerability has been resolved:
xhci: Fix null pointer dereference in remove if xHC has only one roothub
The remove path in xhci platform driver tries to remove and put both main
and shared hcds even if only a main hcd exists (one roothub)
This causes a null pointer dereference in reboot for those controllers.
Check that the shared_hcd exists before trying to remove it. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware_loader: Fix memory leak in firmware upload
In the case of firmware-upload, an instance of struct fw_upload is
allocated in firmware_upload_register(). This data needs to be freed
in fw_dev_release(). Create a new fw_upload_free() function in
sysfs_upload.c to handle the firmware-upload specific memory frees
and incorporate the missing kfree call for the fw_upload structure. |
| In the Linux kernel, the following vulnerability has been resolved:
rcutorture: Fix ksoftirqd boosting timing and iteration
The RCU priority boosting can fail in two situations:
1) If (nr_cpus= > maxcpus=), which means if the total number of CPUs
is higher than those brought online at boot, then torture_onoff() may
later bring up CPUs that weren't online on boot. Now since rcutorture
initialization only boosts the ksoftirqds of the CPUs that have been
set online on boot, the CPUs later set online by torture_onoff won't
benefit from the boost, making RCU priority boosting fail.
2) The ksoftirqd kthreads are boosted after the creation of
rcu_torture_boost() kthreads, which opens a window large enough for these
rcu_torture_boost() kthreads to wait (despite running at FIFO priority)
for ksoftirqds that are still running at SCHED_NORMAL priority.
The issues can trigger for example with:
./kvm.sh --configs TREE01 --kconfig "CONFIG_RCU_BOOST=y"
[ 34.968561] rcu-torture: !!!
[ 34.968627] ------------[ cut here ]------------
[ 35.014054] WARNING: CPU: 4 PID: 114 at kernel/rcu/rcutorture.c:1979 rcu_torture_stats_print+0x5ad/0x610
[ 35.052043] Modules linked in:
[ 35.069138] CPU: 4 PID: 114 Comm: rcu_torture_sta Not tainted 5.18.0-rc1 #1
[ 35.096424] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.14.0-0-g155821a-rebuilt.opensuse.org 04/01/2014
[ 35.154570] RIP: 0010:rcu_torture_stats_print+0x5ad/0x610
[ 35.198527] Code: 63 1b 02 00 74 02 0f 0b 48 83 3d 35 63 1b 02 00 74 02 0f 0b 48 83 3d 21 63 1b 02 00 74 02 0f 0b 48 83 3d 0d 63 1b 02 00 74 02 <0f> 0b 83 eb 01 0f 8e ba fc ff ff 0f 0b e9 b3 fc ff f82
[ 37.251049] RSP: 0000:ffffa92a0050bdf8 EFLAGS: 00010202
[ 37.277320] rcu: De-offloading 8
[ 37.290367] RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000001
[ 37.290387] RDX: 0000000000000000 RSI: 00000000ffffbfff RDI: 00000000ffffffff
[ 37.290398] RBP: 000000000000007b R08: 0000000000000000 R09: c0000000ffffbfff
[ 37.290407] R10: 000000000000002a R11: ffffa92a0050bc18 R12: ffffa92a0050be20
[ 37.290417] R13: ffffa92a0050be78 R14: 0000000000000000 R15: 000000000001bea0
[ 37.290427] FS: 0000000000000000(0000) GS:ffff96045eb00000(0000) knlGS:0000000000000000
[ 37.290448] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 37.290460] CR2: 0000000000000000 CR3: 000000001dc0c000 CR4: 00000000000006e0
[ 37.290470] Call Trace:
[ 37.295049] <TASK>
[ 37.295065] ? preempt_count_add+0x63/0x90
[ 37.295095] ? _raw_spin_lock_irqsave+0x12/0x40
[ 37.295125] ? rcu_torture_stats_print+0x610/0x610
[ 37.295143] rcu_torture_stats+0x29/0x70
[ 37.295160] kthread+0xe3/0x110
[ 37.295176] ? kthread_complete_and_exit+0x20/0x20
[ 37.295193] ret_from_fork+0x22/0x30
[ 37.295218] </TASK>
Fix this with boosting the ksoftirqds kthreads from the boosting
hotplug callback itself and before the boosting kthreads are created. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/ttm: fix CCS handling
Crucible + recent Mesa seems to sometimes hit:
GEM_BUG_ON(num_ccs_blks > NUM_CCS_BLKS_PER_XFER)
And it looks like we can also trigger this with gem_lmem_swapping, if we
modify the test to use slightly larger object sizes.
Looking closer it looks like we have the following issues in
migrate_copy():
- We are using plain integer in various places, which we can easily
overflow with a large object.
- We pass the entire object size (when the src is lmem) into
emit_pte() and then try to copy it, which doesn't work, since we
only have a few fixed sized windows in which to map the pages and
perform the copy. With an object > 8M we therefore aren't properly
copying the pages. And then with an object > 64M we trigger the
GEM_BUG_ON(num_ccs_blks > NUM_CCS_BLKS_PER_XFER).
So it looks like our copy handling for any object > 8M (which is our
CHUNK_SZ) is currently broken on DG2.
Testcase: igt@gem_lmem_swapping
(cherry picked from commit 8676145eb2f53a9940ff70910caf0125bd8a4bc2) |
| In the Linux kernel, the following vulnerability has been resolved:
ath9k: fix use-after-free in ath9k_hif_usb_rx_cb
Syzbot reported use-after-free Read in ath9k_hif_usb_rx_cb() [0]. The
problem was in incorrect htc_handle->drv_priv initialization.
Probable call trace which can trigger use-after-free:
ath9k_htc_probe_device()
/* htc_handle->drv_priv = priv; */
ath9k_htc_wait_for_target() <--- Failed
ieee80211_free_hw() <--- priv pointer is freed
<IRQ>
...
ath9k_hif_usb_rx_cb()
ath9k_hif_usb_rx_stream()
RX_STAT_INC() <--- htc_handle->drv_priv access
In order to not add fancy protection for drv_priv we can move
htc_handle->drv_priv initialization at the end of the
ath9k_htc_probe_device() and add helper macro to make
all *_STAT_* macros NULL safe, since syzbot has reported related NULL
deref in that macros [1] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915: fix null pointer dereference
Asus chromebook CX550 crashes during boot on v5.17-rc1 kernel.
The root cause is null pointer defeference of bi_next
in tgl_get_bw_info() in drivers/gpu/drm/i915/display/intel_bw.c.
BUG: kernel NULL pointer dereference, address: 000000000000002e
PGD 0 P4D 0
Oops: 0002 [#1] PREEMPT SMP NOPTI
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G U 5.17.0-rc1
Hardware name: Google Delbin/Delbin, BIOS Google_Delbin.13672.156.3 05/14/2021
RIP: 0010:tgl_get_bw_info+0x2de/0x510
...
[ 2.554467] Call Trace:
[ 2.554467] <TASK>
[ 2.554467] intel_bw_init_hw+0x14a/0x434
[ 2.554467] ? _printk+0x59/0x73
[ 2.554467] ? _dev_err+0x77/0x91
[ 2.554467] i915_driver_hw_probe+0x329/0x33e
[ 2.554467] i915_driver_probe+0x4c8/0x638
[ 2.554467] i915_pci_probe+0xf8/0x14e
[ 2.554467] ? _raw_spin_unlock_irqrestore+0x12/0x2c
[ 2.554467] pci_device_probe+0xaa/0x142
[ 2.554467] really_probe+0x13f/0x2f4
[ 2.554467] __driver_probe_device+0x9e/0xd3
[ 2.554467] driver_probe_device+0x24/0x7c
[ 2.554467] __driver_attach+0xba/0xcf
[ 2.554467] ? driver_attach+0x1f/0x1f
[ 2.554467] bus_for_each_dev+0x8c/0xc0
[ 2.554467] bus_add_driver+0x11b/0x1f7
[ 2.554467] driver_register+0x60/0xea
[ 2.554467] ? mipi_dsi_bus_init+0x16/0x16
[ 2.554467] i915_init+0x2c/0xb9
[ 2.554467] ? mipi_dsi_bus_init+0x16/0x16
[ 2.554467] do_one_initcall+0x12e/0x2b3
[ 2.554467] do_initcall_level+0xd6/0xf3
[ 2.554467] do_initcalls+0x4e/0x79
[ 2.554467] kernel_init_freeable+0xed/0x14d
[ 2.554467] ? rest_init+0xc1/0xc1
[ 2.554467] kernel_init+0x1a/0x120
[ 2.554467] ret_from_fork+0x1f/0x30
[ 2.554467] </TASK>
...
Kernel panic - not syncing: Fatal exception
(cherry picked from commit c247cd03898c4c43c3bce6d4014730403bc13032) |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: felix: suppress non-changes to the tagging protocol
The way in which dsa_tree_change_tag_proto() works is that when
dsa_tree_notify() fails, it doesn't know whether the operation failed
mid way in a multi-switch tree, or it failed for a single-switch tree.
So even though drivers need to fail cleanly in
ds->ops->change_tag_protocol(), DSA will still call dsa_tree_notify()
again, to restore the old tag protocol for potential switches in the
tree where the change did succeeed (before failing for others).
This means for the felix driver that if we report an error in
felix_change_tag_protocol(), we'll get another call where proto_ops ==
old_proto_ops. If we proceed to act upon that, we may do unexpected
things. For example, we will call dsa_tag_8021q_register() twice in a
row, without any dsa_tag_8021q_unregister() in between. Then we will
actually call dsa_tag_8021q_unregister() via old_proto_ops->teardown,
which (if it manages to run at all, after walking through corrupted data
structures) will leave the ports inoperational anyway.
The bug can be readily reproduced if we force an error while in
tag_8021q mode; this crashes the kernel.
echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
echo edsa > /sys/class/net/eno2/dsa/tagging # -EPROTONOSUPPORT
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000014
Call trace:
vcap_entry_get+0x24/0x124
ocelot_vcap_filter_del+0x198/0x270
felix_tag_8021q_vlan_del+0xd4/0x21c
dsa_switch_tag_8021q_vlan_del+0x168/0x2cc
dsa_switch_event+0x68/0x1170
dsa_tree_notify+0x14/0x34
dsa_port_tag_8021q_vlan_del+0x84/0x110
dsa_tag_8021q_unregister+0x15c/0x1c0
felix_tag_8021q_teardown+0x16c/0x180
felix_change_tag_protocol+0x1bc/0x230
dsa_switch_event+0x14c/0x1170
dsa_tree_change_tag_proto+0x118/0x1c0 |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix inode list leak during backref walking at find_parent_nodes()
During backref walking, at find_parent_nodes(), if we are dealing with a
data extent and we get an error while resolving the indirect backrefs, at
resolve_indirect_refs(), or in the while loop that iterates over the refs
in the direct refs rbtree, we end up leaking the inode lists attached to
the direct refs we have in the direct refs rbtree that were not yet added
to the refs ulist passed as argument to find_parent_nodes(). Since they
were not yet added to the refs ulist and prelim_release() does not free
the lists, on error the caller can only free the lists attached to the
refs that were added to the refs ulist, all the remaining refs get their
inode lists never freed, therefore leaking their memory.
Fix this by having prelim_release() always free any attached inode list
to each ref found in the rbtree, and have find_parent_nodes() set the
ref's inode list to NULL once it transfers ownership of the inode list
to a ref added to the refs ulist passed to find_parent_nodes(). |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: OMAP2+: Fix refcount leak in omap3xxx_prm_late_init
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak. |
