| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
udp: Fix a data-race around sysctl_udp_l3mdev_accept.
While reading sysctl_udp_l3mdev_accept, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: Fix data-races around sysctl_fib_multipath_hash_fields.
While reading sysctl_fib_multipath_hash_fields, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts.
While reading sysctl_tcp_thin_linear_timeouts, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: Fix data-races around sysctl_tcp_recovery.
While reading sysctl_tcp_recovery, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: Fix a data-race around sysctl_tcp_early_retrans.
While reading sysctl_tcp_early_retrans, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: Fix data-races around sysctl_tcp_slow_start_after_idle.
While reading sysctl_tcp_slow_start_after_idle, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix call trace observed during I/O with CMF enabled
The following was seen with CMF enabled:
BUG: using smp_processor_id() in preemptible
code: systemd-udevd/31711
kernel: caller is lpfc_update_cmf_cmd+0x214/0x420 [lpfc]
kernel: CPU: 12 PID: 31711 Comm: systemd-udevd
kernel: Call Trace:
kernel: <TASK>
kernel: dump_stack_lvl+0x44/0x57
kernel: check_preemption_disabled+0xbf/0xe0
kernel: lpfc_update_cmf_cmd+0x214/0x420 [lpfc]
kernel: lpfc_nvme_fcp_io_submit+0x23b4/0x4df0 [lpfc]
this_cpu_ptr() calls smp_processor_id() in a preemptible context.
Fix by using per_cpu_ptr() with raw_smp_processor_id() instead. |
| In the Linux kernel, the following vulnerability has been resolved:
list: fix a data-race around ep->rdllist
ep_poll() first calls ep_events_available() with no lock held and checks
if ep->rdllist is empty by list_empty_careful(), which reads
rdllist->prev. Thus all accesses to it need some protection to avoid
store/load-tearing.
Note INIT_LIST_HEAD_RCU() already has the annotation for both prev
and next.
Commit bf3b9f6372c4 ("epoll: Add busy poll support to epoll with socket
fds.") added the first lockless ep_events_available(), and commit
c5a282e9635e ("fs/epoll: reduce the scope of wq lock in epoll_wait()")
made some ep_events_available() calls lockless and added single call under
a lock, finally commit e59d3c64cba6 ("epoll: eliminate unnecessary lock
for zero timeout") made the last ep_events_available() lockless.
BUG: KCSAN: data-race in do_epoll_wait / do_epoll_wait
write to 0xffff88810480c7d8 of 8 bytes by task 1802 on cpu 0:
INIT_LIST_HEAD include/linux/list.h:38 [inline]
list_splice_init include/linux/list.h:492 [inline]
ep_start_scan fs/eventpoll.c:622 [inline]
ep_send_events fs/eventpoll.c:1656 [inline]
ep_poll fs/eventpoll.c:1806 [inline]
do_epoll_wait+0x4eb/0xf40 fs/eventpoll.c:2234
do_epoll_pwait fs/eventpoll.c:2268 [inline]
__do_sys_epoll_pwait fs/eventpoll.c:2281 [inline]
__se_sys_epoll_pwait+0x12b/0x240 fs/eventpoll.c:2275
__x64_sys_epoll_pwait+0x74/0x80 fs/eventpoll.c:2275
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88810480c7d8 of 8 bytes by task 1799 on cpu 1:
list_empty_careful include/linux/list.h:329 [inline]
ep_events_available fs/eventpoll.c:381 [inline]
ep_poll fs/eventpoll.c:1797 [inline]
do_epoll_wait+0x279/0xf40 fs/eventpoll.c:2234
do_epoll_pwait fs/eventpoll.c:2268 [inline]
__do_sys_epoll_pwait fs/eventpoll.c:2281 [inline]
__se_sys_epoll_pwait+0x12b/0x240 fs/eventpoll.c:2275
__x64_sys_epoll_pwait+0x74/0x80 fs/eventpoll.c:2275
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0xffff88810480c7d0 -> 0xffff888103c15098
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 1799 Comm: syz-fuzzer Tainted: G W 5.17.0-rc7-syzkaller-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix race condition between ext4_write and ext4_convert_inline_data
Hulk Robot reported a BUG_ON:
==================================================================
EXT4-fs error (device loop3): ext4_mb_generate_buddy:805: group 0,
block bitmap and bg descriptor inconsistent: 25 vs 31513 free clusters
kernel BUG at fs/ext4/ext4_jbd2.c:53!
invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 0 PID: 25371 Comm: syz-executor.3 Not tainted 5.10.0+ #1
RIP: 0010:ext4_put_nojournal fs/ext4/ext4_jbd2.c:53 [inline]
RIP: 0010:__ext4_journal_stop+0x10e/0x110 fs/ext4/ext4_jbd2.c:116
[...]
Call Trace:
ext4_write_inline_data_end+0x59a/0x730 fs/ext4/inline.c:795
generic_perform_write+0x279/0x3c0 mm/filemap.c:3344
ext4_buffered_write_iter+0x2e3/0x3d0 fs/ext4/file.c:270
ext4_file_write_iter+0x30a/0x11c0 fs/ext4/file.c:520
do_iter_readv_writev+0x339/0x3c0 fs/read_write.c:732
do_iter_write+0x107/0x430 fs/read_write.c:861
vfs_writev fs/read_write.c:934 [inline]
do_pwritev+0x1e5/0x380 fs/read_write.c:1031
[...]
==================================================================
Above issue may happen as follows:
cpu1 cpu2
__________________________|__________________________
do_pwritev
vfs_writev
do_iter_write
ext4_file_write_iter
ext4_buffered_write_iter
generic_perform_write
ext4_da_write_begin
vfs_fallocate
ext4_fallocate
ext4_convert_inline_data
ext4_convert_inline_data_nolock
ext4_destroy_inline_data_nolock
clear EXT4_STATE_MAY_INLINE_DATA
ext4_map_blocks
ext4_ext_map_blocks
ext4_mb_new_blocks
ext4_mb_regular_allocator
ext4_mb_good_group_nolock
ext4_mb_init_group
ext4_mb_init_cache
ext4_mb_generate_buddy --> error
ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA)
ext4_restore_inline_data
set EXT4_STATE_MAY_INLINE_DATA
ext4_block_write_begin
ext4_da_write_end
ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA)
ext4_write_inline_data_end
handle=NULL
ext4_journal_stop(handle)
__ext4_journal_stop
ext4_put_nojournal(handle)
ref_cnt = (unsigned long)handle
BUG_ON(ref_cnt == 0) ---> BUG_ON
The lock held by ext4_convert_inline_data is xattr_sem, but the lock
held by generic_perform_write is i_rwsem. Therefore, the two locks can
be concurrent.
To solve above issue, we add inode_lock() for ext4_convert_inline_data().
At the same time, move ext4_convert_inline_data() in front of
ext4_punch_hole(), remove similar handling from ext4_punch_hole(). |
| In the Linux kernel, the following vulnerability has been resolved:
nbd: fix race between nbd_alloc_config() and module removal
When nbd module is being removing, nbd_alloc_config() may be
called concurrently by nbd_genl_connect(), although try_module_get()
will return false, but nbd_alloc_config() doesn't handle it.
The race may lead to the leak of nbd_config and its related
resources (e.g, recv_workq) and oops in nbd_read_stat() due
to the unload of nbd module as shown below:
BUG: kernel NULL pointer dereference, address: 0000000000000040
Oops: 0000 [#1] SMP PTI
CPU: 5 PID: 13840 Comm: kworker/u17:33 Not tainted 5.14.0+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
Workqueue: knbd16-recv recv_work [nbd]
RIP: 0010:nbd_read_stat.cold+0x130/0x1a4 [nbd]
Call Trace:
recv_work+0x3b/0xb0 [nbd]
process_one_work+0x1ed/0x390
worker_thread+0x4a/0x3d0
kthread+0x12a/0x150
ret_from_fork+0x22/0x30
Fixing it by checking the return value of try_module_get()
in nbd_alloc_config(). As nbd_alloc_config() may return ERR_PTR(-ENODEV),
assign nbd->config only when nbd_alloc_config() succeeds to ensure
the value of nbd->config is binary (valid or NULL).
Also adding a debug message to check the reference counter
of nbd_config during module removal. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: Fix races among concurrent prealloc proc writes
We have no protection against concurrent PCM buffer preallocation
changes via proc files, and it may potentially lead to UAF or some
weird problem. This patch applies the PCM open_mutex to the proc
write operation for avoiding the racy proc writes and the PCM stream
open (and further operations). |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: Fix race at socket teardown
Fix a race in the xsk socket teardown code that can lead to a NULL pointer
dereference splat. The current xsk unbind code in xsk_unbind_dev() starts by
setting xs->state to XSK_UNBOUND, sets xs->dev to NULL and then waits for any
NAPI processing to terminate using synchronize_net(). After that, the release
code starts to tear down the socket state and free allocated memory.
BUG: kernel NULL pointer dereference, address: 00000000000000c0
PGD 8000000932469067 P4D 8000000932469067 PUD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 25 PID: 69132 Comm: grpcpp_sync_ser Tainted: G I 5.16.0+ #2
Hardware name: Dell Inc. PowerEdge R730/0599V5, BIOS 1.2.10 03/09/2015
RIP: 0010:__xsk_sendmsg+0x2c/0x690
[...]
RSP: 0018:ffffa2348bd13d50 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000040 RCX: ffff8d5fc632d258
RDX: 0000000000400000 RSI: ffffa2348bd13e10 RDI: ffff8d5fc5489800
RBP: ffffa2348bd13db0 R08: 0000000000000000 R09: 00007ffffffff000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8d5fc5489800
R13: ffff8d5fcb0f5140 R14: ffff8d5fcb0f5140 R15: 0000000000000000
FS: 00007f991cff9400(0000) GS:ffff8d6f1f700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000c0 CR3: 0000000114888005 CR4: 00000000001706e0
Call Trace:
<TASK>
? aa_sk_perm+0x43/0x1b0
xsk_sendmsg+0xf0/0x110
sock_sendmsg+0x65/0x70
__sys_sendto+0x113/0x190
? debug_smp_processor_id+0x17/0x20
? fpregs_assert_state_consistent+0x23/0x50
? exit_to_user_mode_prepare+0xa5/0x1d0
__x64_sys_sendto+0x29/0x30
do_syscall_64+0x3b/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
There are two problems with the current code. First, setting xs->dev to NULL
before waiting for all users to stop using the socket is not correct. The
entry to the data plane functions xsk_poll(), xsk_sendmsg(), and xsk_recvmsg()
are all guarded by a test that xs->state is in the state XSK_BOUND and if not,
it returns right away. But one process might have passed this test but still
have not gotten to the point in which it uses xs->dev in the code. In this
interim, a second process executing xsk_unbind_dev() might have set xs->dev to
NULL which will lead to a crash for the first process. The solution here is
just to get rid of this NULL assignment since it is not used anymore. Before
commit 42fddcc7c64b ("xsk: use state member for socket synchronization"),
xs->dev was the gatekeeper to admit processes into the data plane functions,
but it was replaced with the state variable xs->state in the aforementioned
commit.
The second problem is that synchronize_net() does not wait for any process in
xsk_poll(), xsk_sendmsg(), or xsk_recvmsg() to complete, which means that the
state they rely on might be cleaned up prematurely. This can happen when the
notifier gets called (at driver unload for example) as it uses xsk_unbind_dev().
Solve this by extending the RCU critical region from just the ndo_xsk_wakeup
to the whole functions mentioned above, so that both the test of xs->state ==
XSK_BOUND and the last use of any member of xs is covered by the RCU critical
section. This will guarantee that when synchronize_net() completes, there will
be no processes left executing xsk_poll(), xsk_sendmsg(), or xsk_recvmsg() and
state can be cleaned up safely. Note that we need to drop the RCU lock for the
skb xmit path as it uses functions that might sleep. Due to this, we have to
retest the xs->state after we grab the mutex that protects the skb xmit code
from, among a number of things, an xsk_unbind_dev() being executed from the
notifier at the same time. |
| In the Linux kernel, the following vulnerability has been resolved:
ibmvnic: fix race between xmit and reset
There is a race between reset and the transmit paths that can lead to
ibmvnic_xmit() accessing an scrq after it has been freed in the reset
path. It can result in a crash like:
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc0080000016189f8
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0080000016189f8] ibmvnic_xmit+0x60/0xb60 [ibmvnic]
LR [c000000000c0046c] dev_hard_start_xmit+0x11c/0x280
Call Trace:
[c008000001618f08] ibmvnic_xmit+0x570/0xb60 [ibmvnic] (unreliable)
[c000000000c0046c] dev_hard_start_xmit+0x11c/0x280
[c000000000c9cfcc] sch_direct_xmit+0xec/0x330
[c000000000bfe640] __dev_xmit_skb+0x3a0/0x9d0
[c000000000c00ad4] __dev_queue_xmit+0x394/0x730
[c008000002db813c] __bond_start_xmit+0x254/0x450 [bonding]
[c008000002db8378] bond_start_xmit+0x40/0xc0 [bonding]
[c000000000c0046c] dev_hard_start_xmit+0x11c/0x280
[c000000000c00ca4] __dev_queue_xmit+0x564/0x730
[c000000000cf97e0] neigh_hh_output+0xd0/0x180
[c000000000cfa69c] ip_finish_output2+0x31c/0x5c0
[c000000000cfd244] __ip_queue_xmit+0x194/0x4f0
[c000000000d2a3c4] __tcp_transmit_skb+0x434/0x9b0
[c000000000d2d1e0] __tcp_retransmit_skb+0x1d0/0x6a0
[c000000000d2d984] tcp_retransmit_skb+0x34/0x130
[c000000000d310e8] tcp_retransmit_timer+0x388/0x6d0
[c000000000d315ec] tcp_write_timer_handler+0x1bc/0x330
[c000000000d317bc] tcp_write_timer+0x5c/0x200
[c000000000243270] call_timer_fn+0x50/0x1c0
[c000000000243704] __run_timers.part.0+0x324/0x460
[c000000000243894] run_timer_softirq+0x54/0xa0
[c000000000ea713c] __do_softirq+0x15c/0x3e0
[c000000000166258] __irq_exit_rcu+0x158/0x190
[c000000000166420] irq_exit+0x20/0x40
[c00000000002853c] timer_interrupt+0x14c/0x2b0
[c000000000009a00] decrementer_common_virt+0x210/0x220
--- interrupt: 900 at plpar_hcall_norets_notrace+0x18/0x2c
The immediate cause of the crash is the access of tx_scrq in the following
snippet during a reset, where the tx_scrq can be either NULL or an address
that will soon be invalid:
ibmvnic_xmit()
{
...
tx_scrq = adapter->tx_scrq[queue_num];
txq = netdev_get_tx_queue(netdev, queue_num);
ind_bufp = &tx_scrq->ind_buf;
if (test_bit(0, &adapter->resetting)) {
...
}
But beyond that, the call to ibmvnic_xmit() itself is not safe during a
reset and the reset path attempts to avoid this by stopping the queue in
ibmvnic_cleanup(). However just after the queue was stopped, an in-flight
ibmvnic_complete_tx() could have restarted the queue even as the reset is
progressing.
Since the queue was restarted we could get a call to ibmvnic_xmit() which
can then access the bad tx_scrq (or other fields).
We cannot however simply have ibmvnic_complete_tx() check the ->resetting
bit and skip starting the queue. This can race at the "back-end" of a good
reset which just restarted the queue but has not cleared the ->resetting
bit yet. If we skip restarting the queue due to ->resetting being true,
the queue would remain stopped indefinitely potentially leading to transmit
timeouts.
IOW ->resetting is too broad for this purpose. Instead use a new flag
that indicates whether or not the queues are active. Only the open/
reset paths control when the queues are active. ibmvnic_complete_tx()
and others wake up the queue only if the queue is marked active.
So we will have:
A. reset/open thread in ibmvnic_cleanup() and __ibmvnic_open()
->resetting = true
->tx_queues_active = false
disable tx queues
...
->tx_queues_active = true
start tx queues
B. Tx interrupt in ibmvnic_complete_tx():
if (->tx_queues_active)
netif_wake_subqueue();
To ensure that ->tx_queues_active and state of the queues are consistent,
we need a lock which:
- must also be taken in the interrupt path (ibmvnic_complete_tx())
- shared across the multiple
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: fix race when vmap stack overflow
Currently, when detecting vmap stack overflow, riscv firstly switches
to the so called shadow stack, then use this shadow stack to call the
get_overflow_stack() to get the overflow stack. However, there's
a race here if two or more harts use the same shadow stack at the same
time.
To solve this race, we introduce spin_shadow_stack atomic var, which
will be swap between its own address and 0 in atomic way, when the
var is set, it means the shadow_stack is being used; when the var
is cleared, it means the shadow_stack isn't being used.
[Palmer: Add AQ to the swap, and also some comments.] |
| In the Linux kernel, the following vulnerability has been resolved:
char: tpm: Protect tpm_pm_suspend with locks
Currently tpm transactions are executed unconditionally in
tpm_pm_suspend() function, which may lead to races with other tpm
accessors in the system.
Specifically, the hw_random tpm driver makes use of tpm_get_random(),
and this function is called in a loop from a kthread, which means it's
not frozen alongside userspace, and so can race with the work done
during system suspend:
tpm tpm0: tpm_transmit: tpm_recv: error -52
tpm tpm0: invalid TPM_STS.x 0xff, dumping stack for forensics
CPU: 0 PID: 1 Comm: init Not tainted 6.1.0-rc5+ #135
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.0-20220807_005459-localhost 04/01/2014
Call Trace:
tpm_tis_status.cold+0x19/0x20
tpm_transmit+0x13b/0x390
tpm_transmit_cmd+0x20/0x80
tpm1_pm_suspend+0xa6/0x110
tpm_pm_suspend+0x53/0x80
__pnp_bus_suspend+0x35/0xe0
__device_suspend+0x10f/0x350
Fix this by calling tpm_try_get_ops(), which itself is a wrapper around
tpm_chip_start(), but takes the appropriate mutex.
[Jason: reworked commit message, added metadata] |
| In the Linux kernel, the following vulnerability has been resolved:
fscache: Fix oops due to race with cookie_lru and use_cookie
If a cookie expires from the LRU and the LRU_DISCARD flag is set, but
the state machine has not run yet, it's possible another thread can call
fscache_use_cookie and begin to use it.
When the cookie_worker finally runs, it will see the LRU_DISCARD flag
set, transition the cookie->state to LRU_DISCARDING, which will then
withdraw the cookie. Once the cookie is withdrawn the object is removed
the below oops will occur because the object associated with the cookie
is now NULL.
Fix the oops by clearing the LRU_DISCARD bit if another thread uses the
cookie before the cookie_worker runs.
BUG: kernel NULL pointer dereference, address: 0000000000000008
...
CPU: 31 PID: 44773 Comm: kworker/u130:1 Tainted: G E 6.0.0-5.dneg.x86_64 #1
Hardware name: Google Compute Engine/Google Compute Engine, BIOS Google 08/26/2022
Workqueue: events_unbound netfs_rreq_write_to_cache_work [netfs]
RIP: 0010:cachefiles_prepare_write+0x28/0x90 [cachefiles]
...
Call Trace:
netfs_rreq_write_to_cache_work+0x11c/0x320 [netfs]
process_one_work+0x217/0x3e0
worker_thread+0x4a/0x3b0
kthread+0xd6/0x100 |
| In the Linux kernel, the following vulnerability has been resolved:
configfs: fix a race in configfs_{,un}register_subsystem()
When configfs_register_subsystem() or configfs_unregister_subsystem()
is executing link_group() or unlink_group(),
it is possible that two processes add or delete list concurrently.
Some unfortunate interleavings of them can cause kernel panic.
One of cases is:
A --> B --> C --> D
A <-- B <-- C <-- D
delete list_head *B | delete list_head *C
--------------------------------|-----------------------------------
configfs_unregister_subsystem | configfs_unregister_subsystem
unlink_group | unlink_group
unlink_obj | unlink_obj
list_del_init | list_del_init
__list_del_entry | __list_del_entry
__list_del | __list_del
// next == C |
next->prev = prev |
| next->prev = prev
prev->next = next |
| // prev == B
| prev->next = next
Fix this by adding mutex when calling link_group() or unlink_group(),
but parent configfs_subsystem is NULL when config_item is root.
So I create a mutex configfs_subsystem_mutex. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix relocation crash due to premature return from btrfs_commit_transaction()
We are seeing crashes similar to the following trace:
[38.969182] WARNING: CPU: 20 PID: 2105 at fs/btrfs/relocation.c:4070 btrfs_relocate_block_group+0x2dc/0x340 [btrfs]
[38.973556] CPU: 20 PID: 2105 Comm: btrfs Not tainted 5.17.0-rc4 #54
[38.974580] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[38.976539] RIP: 0010:btrfs_relocate_block_group+0x2dc/0x340 [btrfs]
[38.980336] RSP: 0000:ffffb0dd42e03c20 EFLAGS: 00010206
[38.981218] RAX: ffff96cfc4ede800 RBX: ffff96cfc3ce0000 RCX: 000000000002ca14
[38.982560] RDX: 0000000000000000 RSI: 4cfd109a0bcb5d7f RDI: ffff96cfc3ce0360
[38.983619] RBP: ffff96cfc309c000 R08: 0000000000000000 R09: 0000000000000000
[38.984678] R10: ffff96cec0000001 R11: ffffe84c80000000 R12: ffff96cfc4ede800
[38.985735] R13: 0000000000000000 R14: 0000000000000000 R15: ffff96cfc3ce0360
[38.987146] FS: 00007f11c15218c0(0000) GS:ffff96d6dfb00000(0000) knlGS:0000000000000000
[38.988662] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[38.989398] CR2: 00007ffc922c8e60 CR3: 00000001147a6001 CR4: 0000000000370ee0
[38.990279] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[38.991219] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[38.992528] Call Trace:
[38.992854] <TASK>
[38.993148] btrfs_relocate_chunk+0x27/0xe0 [btrfs]
[38.993941] btrfs_balance+0x78e/0xea0 [btrfs]
[38.994801] ? vsnprintf+0x33c/0x520
[38.995368] ? __kmalloc_track_caller+0x351/0x440
[38.996198] btrfs_ioctl_balance+0x2b9/0x3a0 [btrfs]
[38.997084] btrfs_ioctl+0x11b0/0x2da0 [btrfs]
[38.997867] ? mod_objcg_state+0xee/0x340
[38.998552] ? seq_release+0x24/0x30
[38.999184] ? proc_nr_files+0x30/0x30
[38.999654] ? call_rcu+0xc8/0x2f0
[39.000228] ? __x64_sys_ioctl+0x84/0xc0
[39.000872] ? btrfs_ioctl_get_supported_features+0x30/0x30 [btrfs]
[39.001973] __x64_sys_ioctl+0x84/0xc0
[39.002566] do_syscall_64+0x3a/0x80
[39.003011] entry_SYSCALL_64_after_hwframe+0x44/0xae
[39.003735] RIP: 0033:0x7f11c166959b
[39.007324] RSP: 002b:00007fff2543e998 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[39.008521] RAX: ffffffffffffffda RBX: 00007f11c1521698 RCX: 00007f11c166959b
[39.009833] RDX: 00007fff2543ea40 RSI: 00000000c4009420 RDI: 0000000000000003
[39.011270] RBP: 0000000000000003 R08: 0000000000000013 R09: 00007f11c16f94e0
[39.012581] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff25440df3
[39.014046] R13: 0000000000000000 R14: 00007fff2543ea40 R15: 0000000000000001
[39.015040] </TASK>
[39.015418] ---[ end trace 0000000000000000 ]---
[43.131559] ------------[ cut here ]------------
[43.132234] kernel BUG at fs/btrfs/extent-tree.c:2717!
[43.133031] invalid opcode: 0000 [#1] PREEMPT SMP PTI
[43.133702] CPU: 1 PID: 1839 Comm: btrfs Tainted: G W 5.17.0-rc4 #54
[43.134863] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[43.136426] RIP: 0010:unpin_extent_range+0x37a/0x4f0 [btrfs]
[43.139913] RSP: 0000:ffffb0dd4216bc70 EFLAGS: 00010246
[43.140629] RAX: 0000000000000000 RBX: ffff96cfc34490f8 RCX: 0000000000000001
[43.141604] RDX: 0000000080000001 RSI: 0000000051d00000 RDI: 00000000ffffffff
[43.142645] RBP: 0000000000000000 R08: 0000000000000000 R09: ffff96cfd07dca50
[43.143669] R10: ffff96cfc46e8a00 R11: fffffffffffec000 R12: 0000000041d00000
[43.144657] R13: ffff96cfc3ce0000 R14: ffffb0dd4216bd08 R15: 0000000000000000
[43.145686] FS: 00007f7657dd68c0(0000) GS:ffff96d6df640000(0000) knlGS:0000000000000000
[43.146808] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[43.147584] CR2: 00007f7fe81bf5b0 CR3: 00000001093ee004 CR4: 0000000000370ee0
[43.148589] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[43.149581] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 00000000000
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: do not start relocation until in progress drops are done
We hit a bug with a recovering relocation on mount for one of our file
systems in production. I reproduced this locally by injecting errors
into snapshot delete with balance running at the same time. This
presented as an error while looking up an extent item
WARNING: CPU: 5 PID: 1501 at fs/btrfs/extent-tree.c:866 lookup_inline_extent_backref+0x647/0x680
CPU: 5 PID: 1501 Comm: btrfs-balance Not tainted 5.16.0-rc8+ #8
RIP: 0010:lookup_inline_extent_backref+0x647/0x680
RSP: 0018:ffffae0a023ab960 EFLAGS: 00010202
RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 000000000000000c RDI: 0000000000000000
RBP: ffff943fd2a39b60 R08: 0000000000000000 R09: 0000000000000001
R10: 0001434088152de0 R11: 0000000000000000 R12: 0000000001d05000
R13: ffff943fd2a39b60 R14: ffff943fdb96f2a0 R15: ffff9442fc923000
FS: 0000000000000000(0000) GS:ffff944e9eb40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f1157b1fca8 CR3: 000000010f092000 CR4: 0000000000350ee0
Call Trace:
<TASK>
insert_inline_extent_backref+0x46/0xd0
__btrfs_inc_extent_ref.isra.0+0x5f/0x200
? btrfs_merge_delayed_refs+0x164/0x190
__btrfs_run_delayed_refs+0x561/0xfa0
? btrfs_search_slot+0x7b4/0xb30
? btrfs_update_root+0x1a9/0x2c0
btrfs_run_delayed_refs+0x73/0x1f0
? btrfs_update_root+0x1a9/0x2c0
btrfs_commit_transaction+0x50/0xa50
? btrfs_update_reloc_root+0x122/0x220
prepare_to_merge+0x29f/0x320
relocate_block_group+0x2b8/0x550
btrfs_relocate_block_group+0x1a6/0x350
btrfs_relocate_chunk+0x27/0xe0
btrfs_balance+0x777/0xe60
balance_kthread+0x35/0x50
? btrfs_balance+0xe60/0xe60
kthread+0x16b/0x190
? set_kthread_struct+0x40/0x40
ret_from_fork+0x22/0x30
</TASK>
Normally snapshot deletion and relocation are excluded from running at
the same time by the fs_info->cleaner_mutex. However if we had a
pending balance waiting to get the ->cleaner_mutex, and a snapshot
deletion was running, and then the box crashed, we would come up in a
state where we have a half deleted snapshot.
Again, in the normal case the snapshot deletion needs to complete before
relocation can start, but in this case relocation could very well start
before the snapshot deletion completes, as we simply add the root to the
dead roots list and wait for the next time the cleaner runs to clean up
the snapshot.
Fix this by setting a bit on the fs_info if we have any DEAD_ROOT's that
had a pending drop_progress key. If they do then we know we were in the
middle of the drop operation and set a flag on the fs_info. Then
balance can wait until this flag is cleared to start up again.
If there are DEAD_ROOT's that don't have a drop_progress set then we're
safe to start balance right away as we'll be properly protected by the
cleaner_mutex. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dp: do not complete dp_aux_cmd_fifo_tx() if irq is not for aux transfer
There are 3 possible interrupt sources are handled by DP controller,
HPDstatus, Controller state changes and Aux read/write transaction.
At every irq, DP controller have to check isr status of every interrupt
sources and service the interrupt if its isr status bits shows interrupts
are pending. There is potential race condition may happen at current aux
isr handler implementation since it is always complete dp_aux_cmd_fifo_tx()
even irq is not for aux read or write transaction. This may cause aux read
transaction return premature if host aux data read is in the middle of
waiting for sink to complete transferring data to host while irq happen.
This will cause host's receiving buffer contains unexpected data. This
patch fixes this problem by checking aux isr and return immediately at
aux isr handler if there are no any isr status bits set.
Current there is a bug report regrading eDP edid corruption happen during
system booting up. After lengthy debugging to found that VIDEO_READY
interrupt was continuously firing during system booting up which cause
dp_aux_isr() to complete dp_aux_cmd_fifo_tx() prematurely to retrieve data
from aux hardware buffer which is not yet contains complete data transfer
from sink. This cause edid corruption.
Follows are the signature at kernel logs when problem happen,
EDID has corrupt header
panel-simple-dp-aux aux-aea0000.edp: Couldn't identify panel via EDID
Changes in v2:
-- do complete if (ret == IRQ_HANDLED) ay dp-aux_isr()
-- add more commit text
Changes in v3:
-- add Stephen suggested
-- dp_aux_isr() return IRQ_XXX back to caller
-- dp_ctrl_isr() return IRQ_XXX back to caller
Changes in v4:
-- split into two patches
Changes in v5:
-- delete empty line between tags
Changes in v6:
-- remove extra "that" and fixed line more than 75 char at commit text
Patchwork: https://patchwork.freedesktop.org/patch/516121/ |
