| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix incorrect splitting in btrfs_drop_extent_map_range
In production we were seeing a variety of WARN_ON()'s in the extent_map
code, specifically in btrfs_drop_extent_map_range() when we have to call
add_extent_mapping() for our second split.
Consider the following extent map layout
PINNED
[0 16K) [32K, 48K)
and then we call btrfs_drop_extent_map_range for [0, 36K), with
skip_pinned == true. The initial loop will have
start = 0
end = 36K
len = 36K
we will find the [0, 16k) extent, but since we are pinned we will skip
it, which has this code
start = em_end;
if (end != (u64)-1)
len = start + len - em_end;
em_end here is 16K, so now the values are
start = 16K
len = 16K + 36K - 16K = 36K
len should instead be 20K. This is a problem when we find the next
extent at [32K, 48K), we need to split this extent to leave [36K, 48k),
however the code for the split looks like this
split->start = start + len;
split->len = em_end - (start + len);
In this case we have
em_end = 48K
split->start = 16K + 36K // this should be 16K + 20K
split->len = 48K - (16K + 36K) // this overflows as 16K + 36K is 52K
and now we have an invalid extent_map in the tree that potentially
overlaps other entries in the extent map. Even in the non-overlapping
case we will have split->start set improperly, which will cause problems
with any block related calculations.
We don't actually need len in this loop, we can simply use end as our
end point, and only adjust start up when we find a pinned extent we need
to skip.
Adjust the logic to do this, which keeps us from inserting an invalid
extent map.
We only skip_pinned in the relocation case, so this is relatively rare,
except in the case where you are running relocation a lot, which can
happen with auto relocation on. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix exclusive map memory leak
When excl_prog_hash is 0 and excl_prog_hash_size is non-zero, the map also
needs to be freed. Otherwise, the map memory will not be reclaimed, just
like the memory leak problem reported by syzbot [1].
syzbot reported:
BUG: memory leak
backtrace (crc 7b9fb9b4):
map_create+0x322/0x11e0 kernel/bpf/syscall.c:1512
__sys_bpf+0x3556/0x3610 kernel/bpf/syscall.c:6131 |
| In the Linux kernel, the following vulnerability has been resolved:
serial: sc16is7xx: setup GPIO controller later in probe
The GPIO controller component of the sc16is7xx driver is setup too
early, which can result in a race condition where another device tries
to utilise the GPIO lines before the sc16is7xx device has finished
initialising.
This issue manifests itself as an Oops when the GPIO lines are configured:
Unable to handle kernel read from unreadable memory at virtual address
...
pc : sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
lr : sc16is7xx_gpio_direction_output+0x4c/0x108 [sc16is7xx]
...
Call trace:
sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
gpiod_direction_output_raw_commit+0x64/0x318
gpiod_direction_output+0xb0/0x170
create_gpio_led+0xec/0x198
gpio_led_probe+0x16c/0x4f0
platform_drv_probe+0x5c/0xb0
really_probe+0xe8/0x448
driver_probe_device+0xe8/0x138
__device_attach_driver+0x94/0x118
bus_for_each_drv+0x8c/0xe0
__device_attach+0x100/0x1b8
device_initial_probe+0x28/0x38
bus_probe_device+0xa4/0xb0
deferred_probe_work_func+0x90/0xe0
process_one_work+0x1c4/0x480
worker_thread+0x54/0x430
kthread+0x138/0x150
ret_from_fork+0x10/0x1c
This patch moves the setup of the GPIO controller functions to later in the
probe function, ensuring the sc16is7xx device has already finished
initialising by the time other devices try to make use of the GPIO lines.
The error handling has also been reordered to reflect the new
initialisation order. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qedi: Fix use after free bug in qedi_remove()
In qedi_probe() we call __qedi_probe() which initializes
&qedi->recovery_work with qedi_recovery_handler() and
&qedi->board_disable_work with qedi_board_disable_work().
When qedi_schedule_recovery_handler() is called, schedule_delayed_work()
will finally start the work.
In qedi_remove(), which is called to remove the driver, the following
sequence may be observed:
Fix this by finishing the work before cleanup in qedi_remove().
CPU0 CPU1
|qedi_recovery_handler
qedi_remove |
__qedi_remove |
iscsi_host_free |
scsi_host_put |
//free shost |
|iscsi_host_for_each_session
|//use qedi->shost
Cancel recovery_work and board_disable_work in __qedi_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: mte: Avoid setting PG_mte_tagged if no tags cleared or restored
Prior to commit 69e3b846d8a7 ("arm64: mte: Sync tags for pages where PTE
is untagged"), mte_sync_tags() was only called for pte_tagged() entries
(those mapped with PROT_MTE). Therefore mte_sync_tags() could safely use
test_and_set_bit(PG_mte_tagged, &page->flags) without inadvertently
setting PG_mte_tagged on an untagged page.
The above commit was required as guests may enable MTE without any
control at the stage 2 mapping, nor a PROT_MTE mapping in the VMM.
However, the side-effect was that any page with a PTE that looked like
swap (or migration) was getting PG_mte_tagged set automatically. A
subsequent page copy (e.g. migration) copied the tags to the destination
page even if the tags were owned by KASAN.
This issue was masked by the page_kasan_tag_reset() call introduced in
commit e5b8d9218951 ("arm64: mte: reset the page tag in page->flags").
When this commit was reverted (20794545c146), KASAN started reporting
access faults because the overriding tags in a page did not match the
original page->flags (with CONFIG_KASAN_HW_TAGS=y):
BUG: KASAN: invalid-access in copy_page+0x10/0xd0 arch/arm64/lib/copy_page.S:26
Read at addr f5ff000017f2e000 by task syz-executor.1/2218
Pointer tag: [f5], memory tag: [f2]
Move the PG_mte_tagged bit setting from mte_sync_tags() to the actual
place where tags are cleared (mte_sync_page_tags()) or restored
(mte_restore_tags()). |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: call __btrfs_remove_free_space_cache_locked on cache load failure
Now that lockdep is staying enabled through our entire CI runs I started
seeing the following stack in generic/475
------------[ cut here ]------------
WARNING: CPU: 1 PID: 2171864 at fs/btrfs/discard.c:604 btrfs_discard_update_discardable+0x98/0xb0
CPU: 1 PID: 2171864 Comm: kworker/u4:0 Not tainted 5.19.0-rc8+ #789
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-2.fc32 04/01/2014
Workqueue: btrfs-cache btrfs_work_helper
RIP: 0010:btrfs_discard_update_discardable+0x98/0xb0
RSP: 0018:ffffb857c2f7bad0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff8c85c605c200 RCX: 0000000000000001
RDX: 0000000000000000 RSI: ffffffff86807c5b RDI: ffffffff868a831e
RBP: ffff8c85c4c54000 R08: 0000000000000000 R09: 0000000000000000
R10: ffff8c85c66932f0 R11: 0000000000000001 R12: ffff8c85c3899010
R13: ffff8c85d5be4f40 R14: ffff8c85c4c54000 R15: ffff8c86114bfa80
FS: 0000000000000000(0000) GS:ffff8c863bd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f2e7f168160 CR3: 000000010289a004 CR4: 0000000000370ee0
Call Trace:
__btrfs_remove_free_space_cache+0x27/0x30
load_free_space_cache+0xad2/0xaf0
caching_thread+0x40b/0x650
? lock_release+0x137/0x2d0
btrfs_work_helper+0xf2/0x3e0
? lock_is_held_type+0xe2/0x140
process_one_work+0x271/0x590
? process_one_work+0x590/0x590
worker_thread+0x52/0x3b0
? process_one_work+0x590/0x590
kthread+0xf0/0x120
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
This is the code
ctl = block_group->free_space_ctl;
discard_ctl = &block_group->fs_info->discard_ctl;
lockdep_assert_held(&ctl->tree_lock);
We have a temporary free space ctl for loading the free space cache in
order to avoid having allocations happening while we're loading the
cache. When we hit an error we free it all up, however this also calls
btrfs_discard_update_discardable, which requires
block_group->free_space_ctl->tree_lock to be held. However this is our
temporary ctl so this lock isn't held. Fix this by calling
__btrfs_remove_free_space_cache_locked instead so that we only clean up
the entries and do not mess with the discardable stats. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/client: Fix memory leak in drm_client_target_cloned
dmt_mode is allocated and never freed in this function.
It was found with the ast driver, but most drivers using generic fbdev
setup are probably affected.
This fixes the following kmemleak report:
backtrace:
[<00000000b391296d>] drm_mode_duplicate+0x45/0x220 [drm]
[<00000000e45bb5b3>] drm_client_target_cloned.constprop.0+0x27b/0x480 [drm]
[<00000000ed2d3a37>] drm_client_modeset_probe+0x6bd/0xf50 [drm]
[<0000000010e5cc9d>] __drm_fb_helper_initial_config_and_unlock+0xb4/0x2c0 [drm_kms_helper]
[<00000000909f82ca>] drm_fbdev_client_hotplug+0x2bc/0x4d0 [drm_kms_helper]
[<00000000063a69aa>] drm_client_register+0x169/0x240 [drm]
[<00000000a8c61525>] ast_pci_probe+0x142/0x190 [ast]
[<00000000987f19bb>] local_pci_probe+0xdc/0x180
[<000000004fca231b>] work_for_cpu_fn+0x4e/0xa0
[<0000000000b85301>] process_one_work+0x8b7/0x1540
[<000000003375b17c>] worker_thread+0x70a/0xed0
[<00000000b0d43cd9>] kthread+0x29f/0x340
[<000000008d770833>] ret_from_fork+0x1f/0x30
unreferenced object 0xff11000333089a00 (size 128): |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix potential user-after-free
This fixes all instances of which requires to allocate a buffer calling
alloc_skb which may release the chan lock and reacquire later which
makes it possible that the chan is disconnected in the meantime. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: bq27xxx: Fix poll_interval handling and races on remove
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: use work to update rate to avoid RCU warning
The ieee80211_ops::sta_rc_update must be atomic, because
ieee80211_chan_bw_change() holds rcu_read lock while calling
drv_sta_rc_update(), so create a work to do original things.
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 4621 at kernel/rcu/tree_plugin.h:318
rcu_note_context_switch+0x571/0x5d0
CPU: 0 PID: 4621 Comm: kworker/u16:2 Tainted: G W OE
Workqueue: phy3 ieee80211_chswitch_work [mac80211]
RIP: 0010:rcu_note_context_switch+0x571/0x5d0
Call Trace:
<TASK>
__schedule+0xb0/0x1460
? __mod_timer+0x116/0x360
schedule+0x5a/0xc0
schedule_timeout+0x87/0x150
? trace_raw_output_tick_stop+0x60/0x60
wait_for_completion_timeout+0x7b/0x140
usb_start_wait_urb+0x82/0x160 [usbcore
usb_control_msg+0xe3/0x140 [usbcore
rtw_usb_read+0x88/0xe0 [rtw_usb
rtw_usb_read8+0xf/0x10 [rtw_usb
rtw_fw_send_h2c_command+0xa0/0x170 [rtw_core
rtw_fw_send_ra_info+0xc9/0xf0 [rtw_core
drv_sta_rc_update+0x7c/0x160 [mac80211
ieee80211_chan_bw_change+0xfb/0x110 [mac80211
ieee80211_change_chanctx+0x38/0x130 [mac80211
ieee80211_vif_use_reserved_switch+0x34e/0x900 [mac80211
ieee80211_link_use_reserved_context+0x88/0xe0 [mac80211
ieee80211_chswitch_work+0x95/0x170 [mac80211
process_one_work+0x201/0x410
worker_thread+0x4a/0x3b0
? process_one_work+0x410/0x410
kthread+0xe1/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
media: dvb-usb-v2: gl861: Fix null-ptr-deref in gl861_i2c_master_xfer
In gl861_i2c_master_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach gl861_i2c_master_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen.
We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a
("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()") |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-fc: use lock accessing port_state and rport state
nvme_fc_unregister_remote removes the remote port on a lport object at
any point in time when there is no active association. This races with
with the reconnect logic, because nvme_fc_create_association is not
taking a lock to check the port_state and atomically increase the
active count on the rport. |
| In the Linux kernel, the following vulnerability has been resolved:
kheaders: Use array declaration instead of char
Under CONFIG_FORTIFY_SOURCE, memcpy() will check the size of destination
and source buffers. Defining kernel_headers_data as "char" would trip
this check. Since these addresses are treated as byte arrays, define
them as arrays (as done everywhere else).
This was seen with:
$ cat /sys/kernel/kheaders.tar.xz >> /dev/null
detected buffer overflow in memcpy
kernel BUG at lib/string_helpers.c:1027!
...
RIP: 0010:fortify_panic+0xf/0x20
[...]
Call Trace:
<TASK>
ikheaders_read+0x45/0x50 [kheaders]
kernfs_fop_read_iter+0x1a4/0x2f0
... |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/64s: Fix VAS mm use after free
The refcount on mm is dropped before the coprocessor is detached. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl8xxxu: Fix memory leaks with RTL8723BU, RTL8192EU
The wifi + bluetooth combo chip RTL8723BU can leak memory (especially?)
when it's connected to a bluetooth audio device. The busy bluetooth
traffic generates lots of C2H (card to host) messages, which are not
freed correctly.
To fix this, move the dev_kfree_skb() call in rtl8xxxu_c2hcmd_callback()
inside the loop where skb_dequeue() is called.
The RTL8192EU leaks memory because the C2H messages are added to the
queue and left there forever. (This was fine in the past because it
probably wasn't sending any C2H messages until commit e542e66b7c2e
("wifi: rtl8xxxu: gen2: Turn on the rate control"). Since that commit
it sends a C2H message when the TX rate changes.)
To fix this, delete the check for rf_paths > 1 and the goto. Let the
function process the C2H messages from RTL8192EU like the ones from
the other chips.
Theoretically the RTL8188FU could also leak like RTL8723BU, but it
most likely doesn't send C2H messages frequently enough.
This change was tested with RTL8723BU by Erhard F. I tested it with
RTL8188FU and RTL8192EU. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix the error "trying to register non-static key in rxe_cleanup_task"
In the function rxe_create_qp(), rxe_qp_from_init() is called to
initialize qp, internally things like rxe_init_task are not setup until
rxe_qp_init_req().
If an error occurred before this point then the unwind will call
rxe_cleanup() and eventually to rxe_qp_do_cleanup()/rxe_cleanup_task()
which will oops when trying to access the uninitialized spinlock.
If rxe_init_task is not executed, rxe_cleanup_task will not be called. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: Destroy target device if coalesced MMIO unregistration fails
Destroy and free the target coalesced MMIO device if unregistering said
device fails. As clearly noted in the code, kvm_io_bus_unregister_dev()
does not destroy the target device.
BUG: memory leak
unreferenced object 0xffff888112a54880 (size 64):
comm "syz-executor.2", pid 5258, jiffies 4297861402 (age 14.129s)
hex dump (first 32 bytes):
38 c7 67 15 00 c9 ff ff 38 c7 67 15 00 c9 ff ff 8.g.....8.g.....
e0 c7 e1 83 ff ff ff ff 00 30 67 15 00 c9 ff ff .........0g.....
backtrace:
[<0000000006995a8a>] kmalloc include/linux/slab.h:556 [inline]
[<0000000006995a8a>] kzalloc include/linux/slab.h:690 [inline]
[<0000000006995a8a>] kvm_vm_ioctl_register_coalesced_mmio+0x8e/0x3d0 arch/x86/kvm/../../../virt/kvm/coalesced_mmio.c:150
[<00000000022550c2>] kvm_vm_ioctl+0x47d/0x1600 arch/x86/kvm/../../../virt/kvm/kvm_main.c:3323
[<000000008a75102f>] vfs_ioctl fs/ioctl.c:46 [inline]
[<000000008a75102f>] file_ioctl fs/ioctl.c:509 [inline]
[<000000008a75102f>] do_vfs_ioctl+0xbab/0x1160 fs/ioctl.c:696
[<0000000080e3f669>] ksys_ioctl+0x76/0xa0 fs/ioctl.c:713
[<0000000059ef4888>] __do_sys_ioctl fs/ioctl.c:720 [inline]
[<0000000059ef4888>] __se_sys_ioctl fs/ioctl.c:718 [inline]
[<0000000059ef4888>] __x64_sys_ioctl+0x6f/0xb0 fs/ioctl.c:718
[<000000006444fa05>] do_syscall_64+0x9f/0x4e0 arch/x86/entry/common.c:290
[<000000009a4ed50b>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
BUG: leak checking failed |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: set goal start correctly in ext4_mb_normalize_request
We need to set ac_g_ex to notify the goal start used in
ext4_mb_find_by_goal. Set ac_g_ex instead of ac_f_ex in
ext4_mb_normalize_request.
Besides we should assure goal start is in range [first_data_block,
blocks_count) as ext4_mb_initialize_context does.
[ Added a check to make sure size is less than ar->pright; otherwise
we could end up passing an underflowed value of ar->pright - size to
ext4_get_group_no_and_offset(), which will trigger a BUG_ON later on.
- TYT ] |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Check valid rport returned by fc_bsg_to_rport()
Klocwork reported warning of rport maybe NULL and will be dereferenced.
rport returned by call to fc_bsg_to_rport() could be NULL and dereferenced.
Check valid rport returned by fc_bsg_to_rport(). |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: ets: Remove drr class from the active list if it changes to strict
Whenever a user issues an ets qdisc change command, transforming a
drr class into a strict one, the ets code isn't checking whether that
class was in the active list and removing it. This means that, if a
user changes a strict class (which was in the active list) back to a drr
one, that class will be added twice to the active list [1].
Doing so with the following commands:
tc qdisc add dev lo root handle 1: ets bands 2 strict 1
tc qdisc add dev lo parent 1:2 handle 20: \
tbf rate 8bit burst 100b latency 1s
tc filter add dev lo parent 1: basic classid 1:2
ping -c1 -W0.01 -s 56 127.0.0.1
tc qdisc change dev lo root handle 1: ets bands 2 strict 2
tc qdisc change dev lo root handle 1: ets bands 2 strict 1
ping -c1 -W0.01 -s 56 127.0.0.1
Will trigger the following splat with list debug turned on:
[ 59.279014][ T365] ------------[ cut here ]------------
[ 59.279452][ T365] list_add double add: new=ffff88801d60e350, prev=ffff88801d60e350, next=ffff88801d60e2c0.
[ 59.280153][ T365] WARNING: CPU: 3 PID: 365 at lib/list_debug.c:35 __list_add_valid_or_report+0x17f/0x220
[ 59.280860][ T365] Modules linked in:
[ 59.281165][ T365] CPU: 3 UID: 0 PID: 365 Comm: tc Not tainted 6.18.0-rc7-00105-g7e9f13163c13-dirty #239 PREEMPT(voluntary)
[ 59.281977][ T365] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 59.282391][ T365] RIP: 0010:__list_add_valid_or_report+0x17f/0x220
[ 59.282842][ T365] Code: 89 c6 e8 d4 b7 0d ff 90 0f 0b 90 90 31 c0 e9 31 ff ff ff 90 48 c7 c7 e0 a0 22 9f 48 89 f2 48 89 c1 4c 89 c6 e8 b2 b7 0d ff 90 <0f> 0b 90 90 31 c0 e9 0f ff ff ff 48 89 f7 48 89 44 24 10 4c 89 44
...
[ 59.288812][ T365] Call Trace:
[ 59.289056][ T365] <TASK>
[ 59.289224][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.289546][ T365] ets_qdisc_change+0xd2b/0x1e80
[ 59.289891][ T365] ? __lock_acquire+0x7e7/0x1be0
[ 59.290223][ T365] ? __pfx_ets_qdisc_change+0x10/0x10
[ 59.290546][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.290898][ T365] ? __mutex_trylock_common+0xda/0x240
[ 59.291228][ T365] ? __pfx___mutex_trylock_common+0x10/0x10
[ 59.291655][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.291993][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.292313][ T365] ? trace_contention_end+0xc8/0x110
[ 59.292656][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.293022][ T365] ? srso_alias_return_thunk+0x5/0xfbef5
[ 59.293351][ T365] tc_modify_qdisc+0x63a/0x1cf0
Fix this by always checking and removing an ets class from the active list
when changing it to strict.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/tree/net/sched/sch_ets.c?id=ce052b9402e461a9aded599f5b47e76bc727f7de#n663 |
