| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| USB HID protocol dissector infinite loop in Wireshark 4.6.0 to 4.6.4 and 4.4.0 to 4.4.14 allows denial of service |
| DLMS/COSEM protocol dissector infinite loop in Wireshark 4.6.0 to 4.6.4 |
| MBIM protocol dissector infinite loop in Wireshark 4.6.0 to 4.6.4 and 4.4.0 to 4.4.14 allows denial of service |
| OpenFlow v6 protocol dissector infinite loop in Wireshark 4.6.0 to 4.6.4 and 4.4.0 to 4.4.14 allows denial of service |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: iptfs: validate inner IPv4 header length in IPTFS payload
Add validation of the inner IPv4 packet tot_len and ihl fields parsed
from decrypted IPTFS payloads in __input_process_payload(). A crafted
ESP packet containing an inner IPv4 header with tot_len=0 causes an
infinite loop: iplen=0 leads to capturelen=min(0, remaining)=0, so the
data offset never advances and the while(data < tail) loop never
terminates, spinning forever in softirq context.
Reject inner IPv4 packets where tot_len < ihl*4 or ihl*4 < sizeof(struct
iphdr), which catches both the tot_len=0 case and malformed ihl values.
The normal IP stack performs this validation in ip_rcv_core(), but IPTFS
extracts and processes inner packets before they reach that layer. |
| Marked is a markdown parser and compiler. From 18.0.0 to 18.0.1, a critical Denial of Service (DoS) vulnerability exists in marked. By providing a specific 3-byte input sequence a tab, a vertical tab, and a newline (\x09\x0b\n)—an unauthenticated attacker can trigger an infinite recursion loop during parsing. This leads to unbounded memory allocation, causing the host Node.js application to crash via Memory Exhaustion (OOM). This vulnerability is fixed in 18.0.2. |
| In OpenBSD through 7.8, the slaacd and rad daemons have an infinite loop when they receive a crafted ICMPv6 Neighbor Discovery (ND) option (over a local network) with length zero, because of an "nd_opt_len * 8 - 2" expression with no preceding check for whether nd_opt_len is zero. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix ERTM re-init and zero pdu_len infinite loop
l2cap_config_req() processes CONFIG_REQ for channels in BT_CONNECTED
state to support L2CAP reconfiguration (e.g. MTU changes). However,
since both CONF_INPUT_DONE and CONF_OUTPUT_DONE are already set from
the initial configuration, the reconfiguration path falls through to
l2cap_ertm_init(), which re-initializes tx_q, srej_q, srej_list, and
retrans_list without freeing the previous allocations and sets
chan->sdu to NULL without freeing the existing skb. This leaks all
previously allocated ERTM resources.
Additionally, l2cap_parse_conf_req() does not validate the minimum
value of remote_mps derived from the RFC max_pdu_size option. A zero
value propagates to l2cap_segment_sdu() where pdu_len becomes zero,
causing the while loop to never terminate since len is never
decremented, exhausting all available memory.
Fix the double-init by skipping l2cap_ertm_init() and
l2cap_chan_ready() when the channel is already in BT_CONNECTED state,
while still allowing the reconfiguration parameters to be updated
through l2cap_parse_conf_req(). Also add a pdu_len zero check in
l2cap_segment_sdu() as a safeguard. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wlcore: Return -ENOMEM instead of -EAGAIN if there is not enough headroom
Since upstream commit e75665dd0968 ("wifi: wlcore: ensure skb headroom
before skb_push"), wl1271_tx_allocate() and with it
wl1271_prepare_tx_frame() returns -EAGAIN if pskb_expand_head() fails.
However, in wlcore_tx_work_locked(), a return value of -EAGAIN from
wl1271_prepare_tx_frame() is interpreted as the aggregation buffer being
full. This causes the code to flush the buffer, put the skb back at the
head of the queue, and immediately retry the same skb in a tight while
loop.
Because wlcore_tx_work_locked() holds wl->mutex, and the retry happens
immediately with GFP_ATOMIC, this will result in an infinite loop and a
CPU soft lockup. Return -ENOMEM instead so the packet is dropped and
the loop terminates.
The problem was found by an experimental code review agent based on
gemini-3.1-pro while reviewing backports into v6.18.y. |
| A weakness has been identified in Cesanta Mongoose up to 7.20. This vulnerability affects the function handle_opt of the file /src/net_builtin.c of the component TCP Option Handler. This manipulation of the argument optlen causes infinite loop. The attack is possible to be carried out remotely. The exploit has been made available to the public and could be used for attacks. Upgrading to version 7.21 is able to resolve this issue. Upgrading the affected component is advised. VulDB has contacted the vendor early and they confirmed quickly, that this issue got fixed already. |
| Firebird is an open-source relational database management system. In versions prior to 5.0.4, 4.0.7 and 3.0.14, the ClumpletReader::getClumpletSize() function can overflow the totalLength value when parsing a Wide type clumplet, causing an infinite loop. An authenticated user with INSERT privileges on any table can exploit this via a crafted Batch Parameter Block to cause a denial of service against the server. This issue has been fixed in versions 5.0.4, 4.0.7 and 3.0.14. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: fix differential encoding verification
Differential encoding allows loops to be created if it is abused. To
prevent this the unpack should verify that a diff-encode chain
terminates.
Unfortunately the differential encode verification had two bugs.
1. it conflated states that had gone through check and already been
marked, with states that were currently being checked and marked.
This means that loops in the current chain being verified are treated
as a chain that has already been verified.
2. the order bailout on already checked states compared current chain
check iterators j,k instead of using the outer loop iterator i.
Meaning a step backwards in states in the current chain verification
was being mistaken for moving to an already verified state.
Move to a double mark scheme where already verified states get a
different mark, than the current chain being kept. This enables us
to also drop the backwards verification check that was the cause of
the second error as any already verified state is already marked. |
| facil.io is a C micro-framework for web applications. Prior to commit 5128747363055201d3ecf0e29bf0a961703c9fa0, `fio_json_parse` can enter an infinite loop when it encounters a nested JSON value starting with `i` or `I`. The process spins in user space and pegs one CPU core at ~100% instead of returning a parse error. Because `iodine` vendors the same parser code, the issue also affects `iodine` when it parses attacker-controlled JSON. The smallest reproducer I found is `[i`. The quoted-value form that originally exposed the issue, `[""i`, reaches the same bug because the parser tolerates missing commas and then treats the trailing `i` as the start of another value. Commit 5128747363055201d3ecf0e29bf0a961703c9fa0 fixes the issue. |
| There is a defect in the CPython “tarfile” module affecting the “TarFile” extraction and entry enumeration APIs. The tar implementation would process tar archives with negative offsets without error, resulting in an infinite loop and deadlock during the parsing of maliciously crafted tar archives.
This vulnerability can be mitigated by including the following patch after importing the “tarfile” module: https://gist.github.com/sethmlarson/1716ac5b82b73dbcbf23ad2eff8b33e1 |
| Boolean XPath expressions that evaluate to true can cause an infinite loop in logicalQuery.Select, leading to 100% CPU usage. This can be triggered by top-level selectors such as "1=1" or "true()". |
| Loop with Unreachable Exit Condition ('Infinite Loop') vulnerability in coolsnowwolf lede (package/lean/mt/drivers/mt7615d/src/mt_wifi/embedded/security modules). This vulnerability is associated with program files bn_lib.C.
This issue affects lede: through r25.10.1. |
| This affects versions of the package bn.js before 5.2.3. Calling maskn(0) on any BN instance corrupts the internal state, causing toString(), divmod(), and other methods to enter an infinite loop, hanging the process indefinitely. |
| ImageMagick is free and open-source software used for editing and manipulating digital images. Prior to versions 7.1.2-15 and 6.9.13-40, when a PCD file does not contain a valid Sync marker, the DecodeImage() function becomes trapped in an infinite loop while searching for the Sync marker, causing the program to become unresponsive and continuously consume CPU resources, ultimately leading to system resource exhaustion and denial of service. Versions 7.1.2-15 and 6.9.13-40 contain a patch. |
| In the Linux kernel, the following vulnerability has been resolved:
can: gs_usb: gs_usb_receive_bulk_callback(): unanchor URL on usb_submit_urb() error
In commit 7352e1d5932a ("can: gs_usb: gs_usb_receive_bulk_callback(): fix
URB memory leak"), the URB was re-anchored before usb_submit_urb() in
gs_usb_receive_bulk_callback() to prevent a leak of this URB during
cleanup.
However, this patch did not take into account that usb_submit_urb() could
fail. The URB remains anchored and
usb_kill_anchored_urbs(&parent->rx_submitted) in gs_can_close() loops
infinitely since the anchor list never becomes empty.
To fix the bug, unanchor the URB when an usb_submit_urb() error occurs,
also print an info message. |
| iccDEV provides a set of libraries and tools for working with ICC color management profiles. Versions 2.3.1 and below have an infinite loop in the IccProfile.cpp function, CalcProfileID. This issue is fixed in version 2.3.1.1. |
