| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wilc1000: validate assoc response length before subtracting header
wilc_parse_assoc_resp_info() computes the trailing IE length as
ies_len = buffer_len - sizeof(*res);
without first checking that buffer_len is at least sizeof(struct
wilc_assoc_resp) (6 bytes). buffer_len is the length reported for a
received association response (host_int_parse_assoc_resp_info() passes
hif_drv->assoc_resp / assoc_resp_info_len straight in) and must be
validated before the driver accesses the fixed header.
For a frame shorter than the 6-byte fixed header, the subtraction wraps.
For a four-byte response the result is truncated to a u16 ies_len of
65534, so kmemdup() then attempts to copy 65534 bytes starting at
buffer + sizeof(*res), beyond the valid association-response data
(CWE-125). A response shorter than four bytes can also cause an
out-of-bounds read of res->status_code at offsets 2 and 3.
Reject frames too short to hold the fixed header before touching the
header or computing ies_len. Also set the connection status to a failure
on this path: the caller falls through to a
"conn_info->status == WLAN_STATUS_SUCCESS" check after the parser
returns, so leaving the status untouched could let a malformed short
response be treated as a successful association. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB reads in rtw_get_wps_ie()
rtw_get_wps_ie() iterates over IE data from network frames without
validating that the IE header and payload fit within the remaining
buffer before reading them. Specifically:
- in_ie[cnt + 1] is read without checking cnt + 1 < in_len
- memcmp(&in_ie[cnt + 2], ...) accesses cnt + 2 without bounds check
- in_ie[cnt + 1] is used as length without verifying payload fits
Add bounds checks at the top of the loop body to break early if fewer
than 2 bytes remain for the IE header, or if the declared payload
extends past the end of the buffer. Also require at least 4 bytes of
payload before comparing the WPS OUI. |
| In the Linux kernel, the following vulnerability has been resolved:
exec: fix unsigned loop counter wrap in transfer_args_to_stack()
The stop value is derived from bprm->p >> PAGE_SHIFT. The index variable
is an unsigned long. If bprm->p drops below PAGE_SIZE and stop becomes
zero the loop condition index >= stop is always true.
After the index == 0 iteration the decrement wraps to ULONG_MAX and
bprm->page[ULONG_MAX] reads sizeof(void *) bytes in front of the array.
The pointer has wrapped to -1. That garbage pointer is then passed to
kmap_local_page() and PAGE_SIZE bytes are copied from wherever that
lands into the stack of the process being created. And the loop doesn't
terminate either...
Getting there only requires bprm->p < PAGE_SIZE. On !MMU
bprm_set_stack_limit() and bprm_hit_stack_limit() are empty. So the only
constraint on how far bprm->p is pushed down is valid_arg_len(), i.e.
that each individual string still fits in what is left.
bprm->p starts at PAGE_SIZE * MAX_ARG_PAGES - sizeof(void *) so a
single argument or environment string of a little over 31 pages leaves
it in the first page:
Oops - load access fault [#1]
CPU: 0 UID: 0 PID: 1 Comm: victim Not tainted 7.2.0-rc4 #1
epc : __memcpy+0xd4/0xf8
ra : transfer_args_to_stack+0xaa/0xae
s4 : ffffffffffffffff s2 : 0000000000000000
a1 : ffffffdc98000000 a2 : 0000000000001000
status: 0000000a00001880 badaddr: ffffffdc98000000 cause: 0000000000000005
[<801a5324>] __memcpy+0xd4/0xf8
[<800d5f6a>] load_flat_binary+0x43a/0x65e
[<800a2de4>] bprm_execve+0x1d4/0x316
[<800a351a>] do_execveat_common+0x12e/0x138
[<800a3d44>] __riscv_sys_execve+0x38/0x4e
Kernel panic - not syncing: Fatal exception in interrupt
This is an arcane bug but we should still fix it.
Count down from MAX_ARG_PAGES so the loop ends when index reaches stop,
stop == 0 included. The iterations performed are unchanged for every
other value of stop.
Only CONFIG_MMU=n builds are affected, transfer_args_to_stack() is used
by binfmt_flat and binfmt_elf_fdpic on nommu only.
The loop predates git history. commit 7e7ec6a93434
("elf_fdpic_transfer_args_to_stack(): make it generic") only moved it
from binfmt_elf_fdpic.c into fs/exec.c and narrowed the copy to the used
part of the first page. The condition and the decrement are unchanged
from 2.6.12-rc2. |
| In the Linux kernel, the following vulnerability has been resolved:
cdrom: fix stack out-of-bounds read in CDROMVOLCTRL
mmc_ioctl_cdrom_volume() first reads the audio control mode page into a
32-byte stack buffer with cgc->buflen set to 24. If the device reports a
block descriptor, the function increases cgc->buflen to include that
descriptor and reads the page again.
For CDROMVOLCTRL, the function then builds a MODE SELECT parameter list
by moving cgc->buffer forward by offset - 8 bytes. This drops the block
descriptor from the outgoing payload and leaves a new 8-byte mode
parameter header in front of the audio control page. However, cgc->buflen
is left unchanged.
With a standard 8-byte block descriptor, cgc->buffer points at buffer + 8
but cgc->buflen remains 32. cdrom_mode_select() therefore asks the low
level packet path to write 32 bytes from that adjusted pointer, reading 8
bytes past the end of the 32-byte stack buffer.
This is not hit by CDROMVOLREAD, and CDROMVOLCTRL only triggers it on
drives that return a non-zero block descriptor length, which helps explain
why it has gone unnoticed. The overread is also sent to the device as
extra MODE SELECT payload, so it may not produce an obvious local failure.
Reduce cgc->buflen by the same amount as the buffer pointer adjustment so
the MODE SELECT transfer covers only the intended parameter list. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate compound request size before reading StructureSize2
When ksmbd validates a compound (chained) SMB2 request,
ksmbd_smb2_check_message() reads pdu->StructureSize2 without first
checking that the compound element is large enough to contain it.
StructureSize2 is a 2-byte field at offset 64
(__SMB2_HEADER_STRUCTURE_SIZE) from the start of each element.
The compound-walking logic only guarantees that a full 64-byte SMB2
header is present for the trailing element: when NextCommand is 0, len is
reduced to the number of bytes remaining after next_smb2_rcv_hdr_off. A
remote client can craft a compound request whose last element has exactly
64 bytes, so the 2-byte StructureSize2 read at offset 64 extends one byte
past the receive buffer, producing a slab-out-of-bounds read.
BUG: KASAN: slab-out-of-bounds in ksmbd_smb2_check_message (fs/smb/server/smb2misc.c:402)
Read of size 2 at addr ffff888012ae31ac by task kworker/0:1/14
The buggy address is located 172 bytes inside of allocated 173-byte region
Workqueue: ksmbd-io handle_ksmbd_work
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
ksmbd_smb2_check_message (fs/smb/server/smb2misc.c:402)
handle_ksmbd_work (fs/smb/server/server.c:119)
process_one_work (kernel/workqueue.c:3314)
worker_thread (kernel/workqueue.c:3397)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
ret_from_fork_asm (arch/x86/entry/entry_64.S:245)
Reject any compound element that is too small to hold StructureSize2
before dereferencing it. |
| In the Linux kernel, the following vulnerability has been resolved:
gtp: check skb_pull_data() return in gtp1u_send_echo_resp()
gtp1u_send_echo_resp() ignores skb_pull_data()'s return value. Its
caller gtp1u_udp_encap_recv() only guarantees 16 bytes (udphdr +
gtp1_header), but the pull requests 20 (gtp1_header_long + udphdr). For
a 16-19 byte echo request the pull fails and returns NULL without
advancing skb->data; execution continues, and the following skb_push()
plus the IP header pushed by iptunnel_xmit() move skb->data below
skb->head, tripping skb_under_panic().
Fix it by dropping the packet when skb_pull_data() fails.
skbuff: skb_under_panic: ...
kernel BUG at net/core/skbuff.c:214!
Call Trace:
skb_push (net/core/skbuff.c:2648)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:82)
gtp_encap_recv (drivers/net/gtp.c:701 drivers/net/gtp.c:808 drivers/net/gtp.c:920)
udp_queue_rcv_one_skb (net/ipv4/udp.c:2388)
...
Kernel panic - not syncing: Fatal exception in interrupt |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: qca: fix NVM tag length underflow in TLV parser
In the TLV_TYPE_NVM branch of qca_tlv_check_data() the tag loop bound is
"while (idx < length - sizeof(struct tlv_type_nvm))". "length" is a signed
int from the firmware TLV header and sizeof(struct tlv_type_nvm) is a
size_t (12), so "length" is converted to size_t and any firmware-supplied
"length" < 12 makes the subtraction wrap to a huge value. The loop body
then reads a 12-byte struct tlv_type_nvm past the end of the short
vmalloc'd firmware buffer (and the EDL_TAG_ID_* handlers can write past it).
Rewrite the bound as "idx + sizeof(struct tlv_type_nvm) <= length"; both
operands are non-negative, so it no longer underflows and a "length" too
small for one record correctly skips the loop.
BUG: KASAN: vmalloc-out-of-bounds in qca_download_firmware.isra.0 (drivers/bluetooth/btqca.c:421)
Read of size 2 at addr ffffc900000e5004 by task kworker/u9:0/52
Workqueue: hci0 hci_power_on
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
qca_download_firmware.isra.0 (drivers/bluetooth/btqca.c:421 drivers/bluetooth/btqca.c:617)
qca_uart_setup (drivers/bluetooth/btqca.c:948)
qca_setup (drivers/bluetooth/hci_qca.c:2029)
hci_uart_setup (drivers/bluetooth/hci_ldisc.c:438)
hci_dev_open_sync (net/bluetooth/hci_sync.c:5227)
hci_power_on (net/bluetooth/hci_core.c:920)
process_one_work (kernel/workqueue.c:3322)
worker_thread (kernel/workqueue.c:3486)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
ret_from_fork_asm (arch/x86/entry/entry_64.S:245) |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: p54: validate RX frame length in p54_rx_eeprom_readback()
p54_rx_eeprom_readback() copies the requested EEPROM slice out of a
device-supplied readback frame without checking that the skb actually holds
that many bytes. Commit da1b9a55ff11 ("wifi: p54: prevent buffer-overflow in
p54_rx_eeprom_readback()") closed the destination overflow by copying a
fixed priv->eeprom_slice_size (and rejecting a mismatched advertised len),
but the source side is still unbounded: nothing verifies the frame is long
enough to supply that many bytes.
A malicious USB device can send a short frame whose advertised len matches
priv->eeprom_slice_size while the payload is truncated. The equality check
passes and memcpy() reads past the end of the skb, leaking adjacent heap:
BUG: KASAN: slab-out-of-bounds in p54_rx (drivers/net/wireless/intersil/p54/txrx.c:507)
Read of size 1016 at addr ffff88800f077114 by task swapper/0/0
Call Trace:
<IRQ>
...
__asan_memcpy (mm/kasan/shadow.c:105)
p54_rx (drivers/net/wireless/intersil/p54/txrx.c:507)
p54u_rx_cb (drivers/net/wireless/intersil/p54/p54usb.c:163)
__usb_hcd_giveback_urb (drivers/usb/core/hcd.c:1657)
dummy_timer (drivers/usb/gadget/udc/dummy_hcd.c:2005)
...
</IRQ>
The buggy address belongs to the object at ffff88800f0770c0
which belongs to the cache skbuff_small_head of size 704
The buggy address is located 84 bytes inside of
allocated 704-byte region [ffff88800f0770c0, ffff88800f077380)
Check that the slice fits in the skb before copying. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: ims-pcu - fix heap-buffer-overflow in ims_pcu_process_data()
The `ims_pcu_process_data()` processes incoming URB data byte by byte.
However, it fails to check if the `read_pos` index exceeds
IMS_PCU_BUF_SIZE.
If a malicious USB device sends a packet larger than IMS_PCU_BUF_SIZE,
`read_pos` will increment indefinitely. Moreover, since `read_pos` is
located immediately after `read_buf`, the attacker can overwrite
`read_pos` itself to arbitrarily control the index.
This manipulated `read_pos` is subsequently used in
`ims_pcu_handle_response()` to copy data into `cmd_buf`, leading to a
heap buffer overflow.
Specifically, an attacker can overwrite the `cmd_done.wait.head` located
at offset 136 relative to `cmd_buf` in the `ims_pcu_handle_response()`.
Consequently, when the driver calls `complete(&pcu->cmd_done)`, it
triggers a control flow hijack by using the manipulated pointer.
Fix this by adding a bounds check for `read_pos` before writing to
`read_buf`. If the packet is too long, discard it, log a warning,
and reset the parser state.
[dtor: factor out resetting packet state, reset checksum as well] |
| Buffer over-read in Windows GDI+ allows an unauthorized attacker to deny service over a network. |
| A vulnerability was detected in Open Asset Import Library Assimp 17c12da. This affects the function Assimp::MDLImporter::AddBonesToNodeGraph_3DGS_MDL7 of the file code/AssetLib/MDL/MDLLoader.cpp of the component Node Parser. The manipulation of the argument bones_num results in heap-based buffer overflow. The attack can be executed remotely. The exploit is now public and may be used. The project was informed of the problem early through an issue report but has not responded yet. |
| In geniezone, there is a possible out of bounds read due to a missing bounds check. This could lead to local information disclosure if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS11036877; Issue ID: MSV-7132. |
| In wifi, there is a possible out of bounds read due to a missing bounds check. This could lead to local information disclosure if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS10960006 / BORA00155314, BORA00155001, BORA00154907; Issue ID: MSV-7570. |
| In ccci, there is a possible out of bounds read due to a missing bounds check. This could lead to local denial of service if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS10981501; Issue ID: MSV-7669. |
| A security vulnerability has been detected in sonos tract up to 0.23.4. This impacts the function Tensor::from_raw_dt_align of the file data/src/tensor.rs of the component ONNX Initializer Loader. Such manipulation leads to incorrect calculation of buffer size. The attack may be launched remotely. The exploit has been disclosed publicly and may be used. The name of the patch is 66b10bda8895f4bfaf8c205361f0125cdf51f99b. It is best practice to apply a patch to resolve this issue. |
| A security vulnerability has been detected in Open Asset Import Library Assimp Assimp 17c12da. The affected element is the function Assimp::MDLImporter::ParseBoneTrafoKeys_3DGS_MDL7 of the file code/AssetLib/MDL/MDLLoader.cpp of the component 3DGS MDL7 Bone Transformation Key Parser. The manipulation of the argument transmatrix_count/pcBoneTransforms leads to buffer overflow. It is possible to initiate the attack remotely. The exploit has been disclosed publicly and may be used. The identifier of the patch is 50d767984e78d51b53e2020fdf0967fd624bc377. It is recommended to apply a patch to fix this issue. |
| A flaw has been found in TRENDnet TV-IP751WIC 11.03.03. This vulnerability affects the function SystemNetworkChanged/SystemDDNSChanged/SystemEmailChanged/SystemFTPChanged/websCheckRealm/FUN_00432574/FUN_0043372C of the component alphapd. Executing a manipulation can lead to stack-based buffer overflow. It is possible to launch the attack remotely. The exploit has been published and may be used. |
| ImpactThe undici WebSocket client is vulnerable to a denial-of-service attack due to improper validation of the server_max_window_bits parameter in the permessage-deflate extension. When a WebSocket client connects to a server, it automatically advertises support for permessage-deflate compression. A malicious server can respond with an out-of-range server_max_window_bits value (outside zlib's valid range of 8-15). When the server subsequently sends a compressed frame, the client attempts to create a zlib InflateRaw instance with the invalid windowBits value, causing a synchronous RangeError exception that is not caught, resulting in immediate process termination.
The vulnerability exists because:
* The isValidClientWindowBits() function only validates that the value contains ASCII digits, not that it falls within the valid range 8-15
* The createInflateRaw() call is not wrapped in a try-catch block
* The resulting exception propagates up through the call stack and crashes the Node.js process |
| A flaw has been found in Comfast CF-N1-S 2.6.0.1. This affects the function get_para_from_uri of the file /cgi-bin/mbox-config of the component URI Parameter Parsing. This manipulation of the argument width/height causes stack-based buffer overflow. The attack can be initiated remotely. |
| A security vulnerability has been detected in UTT HiPER 1250GW up to 3.2.7-210907-180535. Affected by this vulnerability is the function strcpy of the file /goform/aspApBasicConfigUrcp of the component HTTP Handler. The manipulation of the argument pvid leads to stack-based buffer overflow. It is possible to initiate the attack remotely. The exploit has been disclosed publicly and may be used. |
