| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: transfer phy_config_inband() locking responsibility to phylink
Problem description
===================
Lockdep reports a possible circular locking dependency (AB/BA) between
&pl->state_mutex and &phy->lock, as follows.
phylink_resolve() // acquires &pl->state_mutex
-> phylink_major_config()
-> phy_config_inband() // acquires &pl->phydev->lock
whereas all the other call sites where &pl->state_mutex and
&pl->phydev->lock have the locking scheme reversed. Everywhere else,
&pl->phydev->lock is acquired at the top level, and &pl->state_mutex at
the lower level. A clear example is phylink_bringup_phy().
The outlier is the newly introduced phy_config_inband() and the existing
lock order is the correct one. To understand why it cannot be the other
way around, it is sufficient to consider phylink_phy_change(), phylink's
callback from the PHY device's phy->phy_link_change() virtual method,
invoked by the PHY state machine.
phy_link_up() and phy_link_down(), the (indirect) callers of
phylink_phy_change(), are called with &phydev->lock acquired.
Then phylink_phy_change() acquires its own &pl->state_mutex, to
serialize changes made to its pl->phy_state and pl->link_config.
So all other instances of &pl->state_mutex and &phydev->lock must be
consistent with this order.
Problem impact
==============
I think the kernel runs a serious deadlock risk if an existing
phylink_resolve() thread, which results in a phy_config_inband() call,
is concurrent with a phy_link_up() or phy_link_down() call, which will
deadlock on &pl->state_mutex in phylink_phy_change(). Practically
speaking, the impact may be limited by the slow speed of the medium
auto-negotiation protocol, which makes it unlikely for the current state
to still be unresolved when a new one is detected, but I think the
problem is there. Nonetheless, the problem was discovered using lockdep.
Proposed solution
=================
Practically speaking, the phy_config_inband() requirement of having
phydev->lock acquired must transfer to the caller (phylink is the only
caller). There, it must bubble up until immediately before
&pl->state_mutex is acquired, for the cases where that takes place.
Solution details, considerations, notes
=======================================
This is the phy_config_inband() call graph:
sfp_upstream_ops :: connect_phy()
|
v
phylink_sfp_connect_phy()
|
v
phylink_sfp_config_phy()
|
| sfp_upstream_ops :: module_insert()
| |
| v
| phylink_sfp_module_insert()
| |
| | sfp_upstream_ops :: module_start()
| | |
| | v
| | phylink_sfp_module_start()
| | |
| v v
| phylink_sfp_config_optical()
phylink_start() | |
| phylink_resume() v v
| | phylink_sfp_set_config()
| | |
v v v
phylink_mac_initial_config()
| phylink_resolve()
| | phylink_ethtool_ksettings_set()
v v v
phylink_major_config()
|
v
phy_config_inband()
phylink_major_config() caller #1, phylink_mac_initial_config(), does not
acquire &pl->state_mutex nor do its callers. It must acquire
&pl->phydev->lock prior to calling phylink_major_config().
phylink_major_config() caller #2, phylink_resolve() acquires
&pl->state_mutex, thus also needs to acquire &pl->phydev->lock.
phylink_major_config() caller #3, phylink_ethtool_ksettings_set(), is
completely uninteresting, because it only call
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix deadlock triggered by cancel_delayed_work_syn()
The following LOCKDEP was detected:
Workqueue: events smc_lgr_free_work [smc]
WARNING: possible circular locking dependency detected
6.1.0-20221027.rc2.git8.56bc5b569087.300.fc36.s390x+debug #1 Not tainted
------------------------------------------------------
kworker/3:0/176251 is trying to acquire lock:
00000000f1467148 ((wq_completion)smc_tx_wq-00000000#2){+.+.}-{0:0},
at: __flush_workqueue+0x7a/0x4f0
but task is already holding lock:
0000037fffe97dc8 ((work_completion)(&(&lgr->free_work)->work)){+.+.}-{0:0},
at: process_one_work+0x232/0x730
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #4 ((work_completion)(&(&lgr->free_work)->work)){+.+.}-{0:0}:
__lock_acquire+0x58e/0xbd8
lock_acquire.part.0+0xe2/0x248
lock_acquire+0xac/0x1c8
__flush_work+0x76/0xf0
__cancel_work_timer+0x170/0x220
__smc_lgr_terminate.part.0+0x34/0x1c0 [smc]
smc_connect_rdma+0x15e/0x418 [smc]
__smc_connect+0x234/0x480 [smc]
smc_connect+0x1d6/0x230 [smc]
__sys_connect+0x90/0xc0
__do_sys_socketcall+0x186/0x370
__do_syscall+0x1da/0x208
system_call+0x82/0xb0
-> #3 (smc_client_lgr_pending){+.+.}-{3:3}:
__lock_acquire+0x58e/0xbd8
lock_acquire.part.0+0xe2/0x248
lock_acquire+0xac/0x1c8
__mutex_lock+0x96/0x8e8
mutex_lock_nested+0x32/0x40
smc_connect_rdma+0xa4/0x418 [smc]
__smc_connect+0x234/0x480 [smc]
smc_connect+0x1d6/0x230 [smc]
__sys_connect+0x90/0xc0
__do_sys_socketcall+0x186/0x370
__do_syscall+0x1da/0x208
system_call+0x82/0xb0
-> #2 (sk_lock-AF_SMC){+.+.}-{0:0}:
__lock_acquire+0x58e/0xbd8
lock_acquire.part.0+0xe2/0x248
lock_acquire+0xac/0x1c8
lock_sock_nested+0x46/0xa8
smc_tx_work+0x34/0x50 [smc]
process_one_work+0x30c/0x730
worker_thread+0x62/0x420
kthread+0x138/0x150
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
-> #1 ((work_completion)(&(&smc->conn.tx_work)->work)){+.+.}-{0:0}:
__lock_acquire+0x58e/0xbd8
lock_acquire.part.0+0xe2/0x248
lock_acquire+0xac/0x1c8
process_one_work+0x2bc/0x730
worker_thread+0x62/0x420
kthread+0x138/0x150
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
-> #0 ((wq_completion)smc_tx_wq-00000000#2){+.+.}-{0:0}:
check_prev_add+0xd8/0xe88
validate_chain+0x70c/0xb20
__lock_acquire+0x58e/0xbd8
lock_acquire.part.0+0xe2/0x248
lock_acquire+0xac/0x1c8
__flush_workqueue+0xaa/0x4f0
drain_workqueue+0xaa/0x158
destroy_workqueue+0x44/0x2d8
smc_lgr_free+0x9e/0xf8 [smc]
process_one_work+0x30c/0x730
worker_thread+0x62/0x420
kthread+0x138/0x150
__ret_from_fork+0x3c/0x58
ret_from_fork+0xa/0x40
other info that might help us debug this:
Chain exists of:
(wq_completion)smc_tx_wq-00000000#2
--> smc_client_lgr_pending
--> (work_completion)(&(&lgr->free_work)->work)
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock((work_completion)(&(&lgr->free_work)->work));
lock(smc_client_lgr_pending);
lock((work_completion)
(&(&lgr->free_work)->work));
lock((wq_completion)smc_tx_wq-00000000#2);
*** DEADLOCK ***
2 locks held by kworker/3:0/176251:
#0: 0000000080183548
((wq_completion)events){+.+.}-{0:0},
at: process_one_work+0x232/0x730
#1: 0000037fffe97dc8
((work_completion)
(&(&lgr->free_work)->work)){+.+.}-{0:0},
at: process_one_work+0x232/0x730
stack backtr
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Don't call mmput from MMU notifier callback
If the process is exiting, the mmput inside mmu notifier callback from
compactd or fork or numa balancing could release the last reference
of mm struct to call exit_mmap and free_pgtable, this triggers deadlock
with below backtrace.
The deadlock will leak kfd process as mmu notifier release is not called
and cause VRAM leaking.
The fix is to take mm reference mmget_non_zero when adding prange to the
deferred list to pair with mmput in deferred list work.
If prange split and add into pchild list, the pchild work_item.mm is not
used, so remove the mm parameter from svm_range_unmap_split and
svm_range_add_child.
The backtrace of hung task:
INFO: task python:348105 blocked for more than 64512 seconds.
Call Trace:
__schedule+0x1c3/0x550
schedule+0x46/0xb0
rwsem_down_write_slowpath+0x24b/0x4c0
unlink_anon_vmas+0xb1/0x1c0
free_pgtables+0xa9/0x130
exit_mmap+0xbc/0x1a0
mmput+0x5a/0x140
svm_range_cpu_invalidate_pagetables+0x2b/0x40 [amdgpu]
mn_itree_invalidate+0x72/0xc0
__mmu_notifier_invalidate_range_start+0x48/0x60
try_to_unmap_one+0x10fa/0x1400
rmap_walk_anon+0x196/0x460
try_to_unmap+0xbb/0x210
migrate_page_unmap+0x54d/0x7e0
migrate_pages_batch+0x1c3/0xae0
migrate_pages_sync+0x98/0x240
migrate_pages+0x25c/0x520
compact_zone+0x29d/0x590
compact_zone_order+0xb6/0xf0
try_to_compact_pages+0xbe/0x220
__alloc_pages_direct_compact+0x96/0x1a0
__alloc_pages_slowpath+0x410/0x930
__alloc_pages_nodemask+0x3a9/0x3e0
do_huge_pmd_anonymous_page+0xd7/0x3e0
__handle_mm_fault+0x5e3/0x5f0
handle_mm_fault+0xf7/0x2e0
hmm_vma_fault.isra.0+0x4d/0xa0
walk_pmd_range.isra.0+0xa8/0x310
walk_pud_range+0x167/0x240
walk_pgd_range+0x55/0x100
__walk_page_range+0x87/0x90
walk_page_range+0xf6/0x160
hmm_range_fault+0x4f/0x90
amdgpu_hmm_range_get_pages+0x123/0x230 [amdgpu]
amdgpu_ttm_tt_get_user_pages+0xb1/0x150 [amdgpu]
init_user_pages+0xb1/0x2a0 [amdgpu]
amdgpu_amdkfd_gpuvm_alloc_memory_of_gpu+0x543/0x7d0 [amdgpu]
kfd_ioctl_alloc_memory_of_gpu+0x24c/0x4e0 [amdgpu]
kfd_ioctl+0x29d/0x500 [amdgpu]
(cherry picked from commit a29e067bd38946f752b0ef855f3dfff87e77bec7) |
| In the Linux kernel, the following vulnerability has been resolved:
hfsplus: remove mutex_lock check in hfsplus_free_extents
Syzbot reported an issue in hfsplus filesystem:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 4400 at fs/hfsplus/extents.c:346
hfsplus_free_extents+0x700/0xad0
Call Trace:
<TASK>
hfsplus_file_truncate+0x768/0xbb0 fs/hfsplus/extents.c:606
hfsplus_write_begin+0xc2/0xd0 fs/hfsplus/inode.c:56
cont_expand_zero fs/buffer.c:2383 [inline]
cont_write_begin+0x2cf/0x860 fs/buffer.c:2446
hfsplus_write_begin+0x86/0xd0 fs/hfsplus/inode.c:52
generic_cont_expand_simple+0x151/0x250 fs/buffer.c:2347
hfsplus_setattr+0x168/0x280 fs/hfsplus/inode.c:263
notify_change+0xe38/0x10f0 fs/attr.c:420
do_truncate+0x1fb/0x2e0 fs/open.c:65
do_sys_ftruncate+0x2eb/0x380 fs/open.c:193
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
To avoid deadlock, Commit 31651c607151 ("hfsplus: avoid deadlock
on file truncation") unlock extree before hfsplus_free_extents(),
and add check wheather extree is locked in hfsplus_free_extents().
However, when operations such as hfsplus_file_release,
hfsplus_setattr, hfsplus_unlink, and hfsplus_get_block are executed
concurrently in different files, it is very likely to trigger the
WARN_ON, which will lead syzbot and xfstest to consider it as an
abnormality.
The comment above this warning also describes one of the easy
triggering situations, which can easily trigger and cause
xfstest&syzbot to report errors.
[task A] [task B]
->hfsplus_file_release
->hfsplus_file_truncate
->hfs_find_init
->mutex_lock
->mutex_unlock
->hfsplus_write_begin
->hfsplus_get_block
->hfsplus_file_extend
->hfsplus_ext_read_extent
->hfs_find_init
->mutex_lock
->hfsplus_free_extents
WARN_ON(mutex_is_locked) !!!
Several threads could try to lock the shared extents tree.
And warning can be triggered in one thread when another thread
has locked the tree. This is the wrong behavior of the code and
we need to remove the warning. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: don't take dev_replace rwsem on task already holding it
Running fstests btrfs/011 with MKFS_OPTIONS="-O rst" to force the usage of
the RAID stripe-tree, we get the following splat from lockdep:
BTRFS info (device sdd): dev_replace from /dev/sdd (devid 1) to /dev/sdb started
============================================
WARNING: possible recursive locking detected
6.11.0-rc3-btrfs-for-next #599 Not tainted
--------------------------------------------
btrfs/2326 is trying to acquire lock:
ffff88810f215c98 (&fs_info->dev_replace.rwsem){++++}-{3:3}, at: btrfs_map_block+0x39f/0x2250
but task is already holding lock:
ffff88810f215c98 (&fs_info->dev_replace.rwsem){++++}-{3:3}, at: btrfs_map_block+0x39f/0x2250
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&fs_info->dev_replace.rwsem);
lock(&fs_info->dev_replace.rwsem);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by btrfs/2326:
#0: ffff88810f215c98 (&fs_info->dev_replace.rwsem){++++}-{3:3}, at: btrfs_map_block+0x39f/0x2250
stack backtrace:
CPU: 1 UID: 0 PID: 2326 Comm: btrfs Not tainted 6.11.0-rc3-btrfs-for-next #599
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
<TASK>
dump_stack_lvl+0x5b/0x80
__lock_acquire+0x2798/0x69d0
? __pfx___lock_acquire+0x10/0x10
? __pfx___lock_acquire+0x10/0x10
lock_acquire+0x19d/0x4a0
? btrfs_map_block+0x39f/0x2250
? __pfx_lock_acquire+0x10/0x10
? find_held_lock+0x2d/0x110
? lock_is_held_type+0x8f/0x100
down_read+0x8e/0x440
? btrfs_map_block+0x39f/0x2250
? __pfx_down_read+0x10/0x10
? do_raw_read_unlock+0x44/0x70
? _raw_read_unlock+0x23/0x40
btrfs_map_block+0x39f/0x2250
? btrfs_dev_replace_by_ioctl+0xd69/0x1d00
? btrfs_bio_counter_inc_blocked+0xd9/0x2e0
? __kasan_slab_alloc+0x6e/0x70
? __pfx_btrfs_map_block+0x10/0x10
? __pfx_btrfs_bio_counter_inc_blocked+0x10/0x10
? kmem_cache_alloc_noprof+0x1f2/0x300
? mempool_alloc_noprof+0xed/0x2b0
btrfs_submit_chunk+0x28d/0x17e0
? __pfx_btrfs_submit_chunk+0x10/0x10
? bvec_alloc+0xd7/0x1b0
? bio_add_folio+0x171/0x270
? __pfx_bio_add_folio+0x10/0x10
? __kasan_check_read+0x20/0x20
btrfs_submit_bio+0x37/0x80
read_extent_buffer_pages+0x3df/0x6c0
btrfs_read_extent_buffer+0x13e/0x5f0
read_tree_block+0x81/0xe0
read_block_for_search+0x4bd/0x7a0
? __pfx_read_block_for_search+0x10/0x10
btrfs_search_slot+0x78d/0x2720
? __pfx_btrfs_search_slot+0x10/0x10
? lock_is_held_type+0x8f/0x100
? kasan_save_track+0x14/0x30
? __kasan_slab_alloc+0x6e/0x70
? kmem_cache_alloc_noprof+0x1f2/0x300
btrfs_get_raid_extent_offset+0x181/0x820
? __pfx_lock_acquire+0x10/0x10
? __pfx_btrfs_get_raid_extent_offset+0x10/0x10
? down_read+0x194/0x440
? __pfx_down_read+0x10/0x10
? do_raw_read_unlock+0x44/0x70
? _raw_read_unlock+0x23/0x40
btrfs_map_block+0x5b5/0x2250
? __pfx_btrfs_map_block+0x10/0x10
scrub_submit_initial_read+0x8fe/0x11b0
? __pfx_scrub_submit_initial_read+0x10/0x10
submit_initial_group_read+0x161/0x3a0
? lock_release+0x20e/0x710
? __pfx_submit_initial_group_read+0x10/0x10
? __pfx_lock_release+0x10/0x10
scrub_simple_mirror.isra.0+0x3eb/0x580
scrub_stripe+0xe4d/0x1440
? lock_release+0x20e/0x710
? __pfx_scrub_stripe+0x10/0x10
? __pfx_lock_release+0x10/0x10
? do_raw_read_unlock+0x44/0x70
? _raw_read_unlock+0x23/0x40
scrub_chunk+0x257/0x4a0
scrub_enumerate_chunks+0x64c/0xf70
? __mutex_unlock_slowpath+0x147/0x5f0
? __pfx_scrub_enumerate_chunks+0x10/0x10
? bit_wait_timeout+0xb0/0x170
? __up_read+0x189/0x700
? scrub_workers_get+0x231/0x300
? up_write+0x490/0x4f0
btrfs_scrub_dev+0x52e/0xcd0
? create_pending_snapshots+0x230/0x250
? __pfx_btrfs_scrub_dev+0x10/0x10
btrfs_dev_replace_by_ioctl+0xd69/0x1d00
? lock_acquire+0x19d/0x4a0
? __pfx_btrfs_dev_replace_by_ioctl+0x10/0x10
?
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: megaraid_sas: Fix for a potential deadlock
This fixes a 'possible circular locking dependency detected' warning
CPU0 CPU1
---- ----
lock(&instance->reset_mutex);
lock(&shost->scan_mutex);
lock(&instance->reset_mutex);
lock(&shost->scan_mutex);
Fix this by temporarily releasing the reset_mutex. |
| In the Linux kernel, the following vulnerability has been resolved:
dma-debug: fix a possible deadlock on radix_lock
radix_lock() shouldn't be held while holding dma_hash_entry[idx].lock
otherwise, there's a possible deadlock scenario when
dma debug API is called holding rq_lock():
CPU0 CPU1 CPU2
dma_free_attrs()
check_unmap() add_dma_entry() __schedule() //out
(A) rq_lock()
get_hash_bucket()
(A) dma_entry_hash
check_sync()
(A) radix_lock() (W) dma_entry_hash
dma_entry_free()
(W) radix_lock()
// CPU2's one
(W) rq_lock()
CPU1 situation can happen when it extending radix tree and
it tries to wake up kswapd via wake_all_kswapd().
CPU2 situation can happen while perf_event_task_sched_out()
(i.e. dma sync operation is called while deleting perf_event using
etm and etr tmc which are Arm Coresight hwtracing driver backends).
To remove this possible situation, call dma_entry_free() after
put_hash_bucket() in check_unmap(). |
| In the Linux kernel, the following vulnerability has been resolved:
nilfs2: fix potential hang in nilfs_detach_log_writer()
Syzbot has reported a potential hang in nilfs_detach_log_writer() called
during nilfs2 unmount.
Analysis revealed that this is because nilfs_segctor_sync(), which
synchronizes with the log writer thread, can be called after
nilfs_segctor_destroy() terminates that thread, as shown in the call trace
below:
nilfs_detach_log_writer
nilfs_segctor_destroy
nilfs_segctor_kill_thread --> Shut down log writer thread
flush_work
nilfs_iput_work_func
nilfs_dispose_list
iput
nilfs_evict_inode
nilfs_transaction_commit
nilfs_construct_segment (if inode needs sync)
nilfs_segctor_sync --> Attempt to synchronize with
log writer thread
*** DEADLOCK ***
Fix this issue by changing nilfs_segctor_sync() so that the log writer
thread returns normally without synchronizing after it terminates, and by
forcing tasks that are already waiting to complete once after the thread
terminates.
The skipped inode metadata flushout will then be processed together in the
subsequent cleanup work in nilfs_segctor_destroy(). |
| In the Linux kernel, the following vulnerability has been resolved:
nouveau: offload fence uevents work to workqueue
This should break the deadlock between the fctx lock and the irq lock.
This offloads the processing off the work from the irq into a workqueue. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid10: prevent soft lockup while flush writes
Currently, there is no limit for raid1/raid10 plugged bio. While flushing
writes, raid1 has cond_resched() while raid10 doesn't, and too many
writes can cause soft lockup.
Follow up soft lockup can be triggered easily with writeback test for
raid10 with ramdisks:
watchdog: BUG: soft lockup - CPU#10 stuck for 27s! [md0_raid10:1293]
Call Trace:
<TASK>
call_rcu+0x16/0x20
put_object+0x41/0x80
__delete_object+0x50/0x90
delete_object_full+0x2b/0x40
kmemleak_free+0x46/0xa0
slab_free_freelist_hook.constprop.0+0xed/0x1a0
kmem_cache_free+0xfd/0x300
mempool_free_slab+0x1f/0x30
mempool_free+0x3a/0x100
bio_free+0x59/0x80
bio_put+0xcf/0x2c0
free_r10bio+0xbf/0xf0
raid_end_bio_io+0x78/0xb0
one_write_done+0x8a/0xa0
raid10_end_write_request+0x1b4/0x430
bio_endio+0x175/0x320
brd_submit_bio+0x3b9/0x9b7 [brd]
__submit_bio+0x69/0xe0
submit_bio_noacct_nocheck+0x1e6/0x5a0
submit_bio_noacct+0x38c/0x7e0
flush_pending_writes+0xf0/0x240
raid10d+0xac/0x1ed0
Fix the problem by adding cond_resched() to raid10 like what raid1 did.
Note that unlimited plugged bio still need to be optimized, for example,
in the case of lots of dirty pages writeback, this will take lots of
memory and io will spend a long time in plug, hence io latency is bad. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/swapfile: add cond_resched() in get_swap_pages()
The softlockup still occurs in get_swap_pages() under memory pressure. 64
CPU cores, 64GB memory, and 28 zram devices, the disksize of each zram
device is 50MB with same priority as si. Use the stress-ng tool to
increase memory pressure, causing the system to oom frequently.
The plist_for_each_entry_safe() loops in get_swap_pages() could reach tens
of thousands of times to find available space (extreme case:
cond_resched() is not called in scan_swap_map_slots()). Let's add
cond_resched() into get_swap_pages() when failed to find available space
to avoid softlockup. |
| In the Linux kernel, the following vulnerability has been resolved:
can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock
The following 3 locks would race against each other, causing the
deadlock situation in the Syzbot bug report:
- j1939_socks_lock
- active_session_list_lock
- sk_session_queue_lock
A reasonable fix is to change j1939_socks_lock to an rwlock, since in
the rare situations where a write lock is required for the linked list
that j1939_socks_lock is protecting, the code does not attempt to
acquire any more locks. This would break the circular lock dependency,
where, for example, the current thread already locks j1939_socks_lock
and attempts to acquire sk_session_queue_lock, and at the same time,
another thread attempts to acquire j1939_socks_lock while holding
sk_session_queue_lock.
NOTE: This patch along does not fix the unregister_netdevice bug
reported by Syzbot; instead, it solves a deadlock situation to prepare
for one or more further patches to actually fix the Syzbot bug, which
appears to be a reference counting problem within the j1939 codebase.
[mkl: remove unrelated newline change] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rt2x00: restart beacon queue when hardware reset
When a hardware reset is triggered, all registers are reset, so all
queues are forced to stop in hardware interface. However, mac80211
will not automatically stop the queue. If we don't manually stop the
beacon queue, the queue will be deadlocked and unable to start again.
This patch fixes the issue where Apple devices cannot connect to the
AP after calling ieee80211_restart_hw(). |
| In the Linux kernel, the following vulnerability has been resolved:
IB/ipoib: Fix mcast list locking
Releasing the `priv->lock` while iterating the `priv->multicast_list` in
`ipoib_mcast_join_task()` opens a window for `ipoib_mcast_dev_flush()` to
remove the items while in the middle of iteration. If the mcast is removed
while the lock was dropped, the for loop spins forever resulting in a hard
lockup (as was reported on RHEL 4.18.0-372.75.1.el8_6 kernel):
Task A (kworker/u72:2 below) | Task B (kworker/u72:0 below)
-----------------------------------+-----------------------------------
ipoib_mcast_join_task(work) | ipoib_ib_dev_flush_light(work)
spin_lock_irq(&priv->lock) | __ipoib_ib_dev_flush(priv, ...)
list_for_each_entry(mcast, | ipoib_mcast_dev_flush(dev = priv->dev)
&priv->multicast_list, list) |
ipoib_mcast_join(dev, mcast) |
spin_unlock_irq(&priv->lock) |
| spin_lock_irqsave(&priv->lock, flags)
| list_for_each_entry_safe(mcast, tmcast,
| &priv->multicast_list, list)
| list_del(&mcast->list);
| list_add_tail(&mcast->list, &remove_list)
| spin_unlock_irqrestore(&priv->lock, flags)
spin_lock_irq(&priv->lock) |
| ipoib_mcast_remove_list(&remove_list)
(Here, `mcast` is no longer on the | list_for_each_entry_safe(mcast, tmcast,
`priv->multicast_list` and we keep | remove_list, list)
spinning on the `remove_list` of | >>> wait_for_completion(&mcast->done)
the other thread which is blocked |
and the list is still valid on |
it's stack.)
Fix this by keeping the lock held and changing to GFP_ATOMIC to prevent
eventual sleeps.
Unfortunately we could not reproduce the lockup and confirm this fix but
based on the code review I think this fix should address such lockups.
crash> bc 31
PID: 747 TASK: ff1c6a1a007e8000 CPU: 31 COMMAND: "kworker/u72:2"
--
[exception RIP: ipoib_mcast_join_task+0x1b1]
RIP: ffffffffc0944ac1 RSP: ff646f199a8c7e00 RFLAGS: 00000002
RAX: 0000000000000000 RBX: ff1c6a1a04dc82f8 RCX: 0000000000000000
work (&priv->mcast_task{,.work})
RDX: ff1c6a192d60ac68 RSI: 0000000000000286 RDI: ff1c6a1a04dc8000
&mcast->list
RBP: ff646f199a8c7e90 R8: ff1c699980019420 R9: ff1c6a1920c9a000
R10: ff646f199a8c7e00 R11: ff1c6a191a7d9800 R12: ff1c6a192d60ac00
mcast
R13: ff1c6a1d82200000 R14: ff1c6a1a04dc8000 R15: ff1c6a1a04dc82d8
dev priv (&priv->lock) &priv->multicast_list (aka head)
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
--- <NMI exception stack> ---
#5 [ff646f199a8c7e00] ipoib_mcast_join_task+0x1b1 at ffffffffc0944ac1 [ib_ipoib]
#6 [ff646f199a8c7e98] process_one_work+0x1a7 at ffffffff9bf10967
crash> rx ff646f199a8c7e68
ff646f199a8c7e68: ff1c6a1a04dc82f8 <<< work = &priv->mcast_task.work
crash> list -hO ipoib_dev_priv.multicast_list ff1c6a1a04dc8000
(empty)
crash> ipoib_dev_priv.mcast_task.work.func,mcast_mutex.owner.counter ff1c6a1a04dc8000
mcast_task.work.func = 0xffffffffc0944910 <ipoib_mcast_join_task>,
mcast_mutex.owner.counter = 0xff1c69998efec000
crash> b 8
PID: 8 TASK: ff1c69998efec000 CPU: 33 COMMAND: "kworker/u72:0"
--
#3 [ff646f1980153d50] wait_for_completion+0x96 at ffffffff9c7d7646
#4 [ff646f1980153d90] ipoib_mcast_remove_list+0x56 at ffffffffc0944dc6 [ib_ipoib]
#5 [ff646f1980153de8] ipoib_mcast_dev_flush+0x1a7 at ffffffffc09455a7 [ib_ipoib]
#6 [ff646f1980153e58] __ipoib_ib_dev_flush+0x1a4 at ffffffffc09431a4 [ib_ipoib]
#7 [ff
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
dma-debug: don't call __dma_entry_alloc_check_leak() under free_entries_lock
__dma_entry_alloc_check_leak() calls into printk -> serial console
output (qcom geni) and grabs port->lock under free_entries_lock
spin lock, which is a reverse locking dependency chain as qcom_geni
IRQ handler can call into dma-debug code and grab free_entries_lock
under port->lock.
Move __dma_entry_alloc_check_leak() call out of free_entries_lock
scope so that we don't acquire serial console's port->lock under it.
Trimmed-down lockdep splat:
The existing dependency chain (in reverse order) is:
-> #2 (free_entries_lock){-.-.}-{2:2}:
_raw_spin_lock_irqsave+0x60/0x80
dma_entry_alloc+0x38/0x110
debug_dma_map_page+0x60/0xf8
dma_map_page_attrs+0x1e0/0x230
dma_map_single_attrs.constprop.0+0x6c/0xc8
geni_se_rx_dma_prep+0x40/0xcc
qcom_geni_serial_isr+0x310/0x510
__handle_irq_event_percpu+0x110/0x244
handle_irq_event_percpu+0x20/0x54
handle_irq_event+0x50/0x88
handle_fasteoi_irq+0xa4/0xcc
handle_irq_desc+0x28/0x40
generic_handle_domain_irq+0x24/0x30
gic_handle_irq+0xc4/0x148
do_interrupt_handler+0xa4/0xb0
el1_interrupt+0x34/0x64
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x64/0x68
arch_local_irq_enable+0x4/0x8
____do_softirq+0x18/0x24
...
-> #1 (&port_lock_key){-.-.}-{2:2}:
_raw_spin_lock_irqsave+0x60/0x80
qcom_geni_serial_console_write+0x184/0x1dc
console_flush_all+0x344/0x454
console_unlock+0x94/0xf0
vprintk_emit+0x238/0x24c
vprintk_default+0x3c/0x48
vprintk+0xb4/0xbc
_printk+0x68/0x90
register_console+0x230/0x38c
uart_add_one_port+0x338/0x494
qcom_geni_serial_probe+0x390/0x424
platform_probe+0x70/0xc0
really_probe+0x148/0x280
__driver_probe_device+0xfc/0x114
driver_probe_device+0x44/0x100
__device_attach_driver+0x64/0xdc
bus_for_each_drv+0xb0/0xd8
__device_attach+0xe4/0x140
device_initial_probe+0x1c/0x28
bus_probe_device+0x44/0xb0
device_add+0x538/0x668
of_device_add+0x44/0x50
of_platform_device_create_pdata+0x94/0xc8
of_platform_bus_create+0x270/0x304
of_platform_populate+0xac/0xc4
devm_of_platform_populate+0x60/0xac
geni_se_probe+0x154/0x160
platform_probe+0x70/0xc0
...
-> #0 (console_owner){-...}-{0:0}:
__lock_acquire+0xdf8/0x109c
lock_acquire+0x234/0x284
console_flush_all+0x330/0x454
console_unlock+0x94/0xf0
vprintk_emit+0x238/0x24c
vprintk_default+0x3c/0x48
vprintk+0xb4/0xbc
_printk+0x68/0x90
dma_entry_alloc+0xb4/0x110
debug_dma_map_sg+0xdc/0x2f8
__dma_map_sg_attrs+0xac/0xe4
dma_map_sgtable+0x30/0x4c
get_pages+0x1d4/0x1e4 [msm]
msm_gem_pin_pages_locked+0x38/0xac [msm]
msm_gem_pin_vma_locked+0x58/0x88 [msm]
msm_ioctl_gem_submit+0xde4/0x13ac [msm]
drm_ioctl_kernel+0xe0/0x15c
drm_ioctl+0x2e8/0x3f4
vfs_ioctl+0x30/0x50
...
Chain exists of:
console_owner --> &port_lock_key --> free_entries_lock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(free_entries_lock);
lock(&port_lock_key);
lock(free_entries_lock);
lock(console_owner);
*** DEADLOCK ***
Call trace:
dump_backtrace+0xb4/0xf0
show_stack+0x20/0x30
dump_stack_lvl+0x60/0x84
dump_stack+0x18/0x24
print_circular_bug+0x1cc/0x234
check_noncircular+0x78/0xac
__lock_acquire+0xdf8/0x109c
lock_acquire+0x234/0x284
console_flush_all+0x330/0x454
consol
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/arm-smmu-v3: Fix soft lockup triggered by arm_smmu_mm_invalidate_range
When running an SVA case, the following soft lockup is triggered:
--------------------------------------------------------------------
watchdog: BUG: soft lockup - CPU#244 stuck for 26s!
pstate: 83400009 (Nzcv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--)
pc : arm_smmu_cmdq_issue_cmdlist+0x178/0xa50
lr : arm_smmu_cmdq_issue_cmdlist+0x150/0xa50
sp : ffff8000d83ef290
x29: ffff8000d83ef290 x28: 000000003b9aca00 x27: 0000000000000000
x26: ffff8000d83ef3c0 x25: da86c0812194a0e8 x24: 0000000000000000
x23: 0000000000000040 x22: ffff8000d83ef340 x21: ffff0000c63980c0
x20: 0000000000000001 x19: ffff0000c6398080 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: ffff3000b4a3bbb0
x14: ffff3000b4a30888 x13: ffff3000b4a3cf60 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : ffffc08120e4d6bc
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000048cfa
x5 : 0000000000000000 x4 : 0000000000000001 x3 : 000000000000000a
x2 : 0000000080000000 x1 : 0000000000000000 x0 : 0000000000000001
Call trace:
arm_smmu_cmdq_issue_cmdlist+0x178/0xa50
__arm_smmu_tlb_inv_range+0x118/0x254
arm_smmu_tlb_inv_range_asid+0x6c/0x130
arm_smmu_mm_invalidate_range+0xa0/0xa4
__mmu_notifier_invalidate_range_end+0x88/0x120
unmap_vmas+0x194/0x1e0
unmap_region+0xb4/0x144
do_mas_align_munmap+0x290/0x490
do_mas_munmap+0xbc/0x124
__vm_munmap+0xa8/0x19c
__arm64_sys_munmap+0x28/0x50
invoke_syscall+0x78/0x11c
el0_svc_common.constprop.0+0x58/0x1c0
do_el0_svc+0x34/0x60
el0_svc+0x2c/0xd4
el0t_64_sync_handler+0x114/0x140
el0t_64_sync+0x1a4/0x1a8
--------------------------------------------------------------------
Note that since 6.6-rc1 the arm_smmu_mm_invalidate_range above is renamed
to "arm_smmu_mm_arch_invalidate_secondary_tlbs", yet the problem remains.
The commit 06ff87bae8d3 ("arm64: mm: remove unused functions and variable
protoypes") fixed a similar lockup on the CPU MMU side. Yet, it can occur
to SMMU too, since arm_smmu_mm_arch_invalidate_secondary_tlbs() is called
typically next to MMU tlb flush function, e.g.
tlb_flush_mmu_tlbonly {
tlb_flush {
__flush_tlb_range {
// check MAX_TLBI_OPS
}
}
mmu_notifier_arch_invalidate_secondary_tlbs {
arm_smmu_mm_arch_invalidate_secondary_tlbs {
// does not check MAX_TLBI_OPS
}
}
}
Clone a CMDQ_MAX_TLBI_OPS from the MAX_TLBI_OPS in tlbflush.h, since in an
SVA case SMMU uses the CPU page table, so it makes sense to align with the
tlbflush code. Then, replace per-page TLBI commands with a single per-asid
TLBI command, if the request size hits this threshold. |
| An issue was discovered in PyTorch v2.5 and v2.7.1. Omission of profiler.stop() can cause torch.profiler.profile (PythonTracer) to crash or hang during finalization, leading to a Denial of Service (DoS). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix deadlock between rcu_tasks_trace and event_mutex.
Fix the following deadlock:
CPU A
_free_event()
perf_kprobe_destroy()
mutex_lock(&event_mutex)
perf_trace_event_unreg()
synchronize_rcu_tasks_trace()
There are several paths where _free_event() grabs event_mutex
and calls sync_rcu_tasks_trace. Above is one such case.
CPU B
bpf_prog_test_run_syscall()
rcu_read_lock_trace()
bpf_prog_run_pin_on_cpu()
bpf_prog_load()
bpf_tracing_func_proto()
trace_set_clr_event()
mutex_lock(&event_mutex)
Delegate trace_set_clr_event() to workqueue to avoid
such lock dependency. |
| In the Linux kernel, the following vulnerability has been resolved:
um: work around sched_yield not yielding in time-travel mode
sched_yield by a userspace may not actually cause scheduling in
time-travel mode as no time has passed. In the case seen it appears to
be a badly implemented userspace spinlock in ASAN. Unfortunately, with
time-travel it causes an extreme slowdown or even deadlock depending on
the kernel configuration (CONFIG_UML_MAX_USERSPACE_ITERATIONS).
Work around it by accounting time to the process whenever it executes a
sched_yield syscall. |
| In the Linux kernel, the following vulnerability has been resolved:
PM: hibernate: Avoid deadlock in hibernate_compressor_param_set()
syzbot reported a deadlock in lock_system_sleep() (see below).
The write operation to "/sys/module/hibernate/parameters/compressor"
conflicts with the registration of ieee80211 device, resulting in a deadlock
when attempting to acquire system_transition_mutex under param_lock.
To avoid this deadlock, change hibernate_compressor_param_set() to use
mutex_trylock() for attempting to acquire system_transition_mutex and
return -EBUSY when it fails.
Task flags need not be saved or adjusted before calling
mutex_trylock(&system_transition_mutex) because the caller is not going
to end up waiting for this mutex and if it runs concurrently with system
suspend in progress, it will be frozen properly when it returns to user
space.
syzbot report:
syz-executor895/5833 is trying to acquire lock:
ffffffff8e0828c8 (system_transition_mutex){+.+.}-{4:4}, at: lock_system_sleep+0x87/0xa0 kernel/power/main.c:56
but task is already holding lock:
ffffffff8e07dc68 (param_lock){+.+.}-{4:4}, at: kernel_param_lock kernel/params.c:607 [inline]
ffffffff8e07dc68 (param_lock){+.+.}-{4:4}, at: param_attr_store+0xe6/0x300 kernel/params.c:586
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (param_lock){+.+.}-{4:4}:
__mutex_lock_common kernel/locking/mutex.c:585 [inline]
__mutex_lock+0x19b/0xb10 kernel/locking/mutex.c:730
ieee80211_rate_control_ops_get net/mac80211/rate.c:220 [inline]
rate_control_alloc net/mac80211/rate.c:266 [inline]
ieee80211_init_rate_ctrl_alg+0x18d/0x6b0 net/mac80211/rate.c:1015
ieee80211_register_hw+0x20cd/0x4060 net/mac80211/main.c:1531
mac80211_hwsim_new_radio+0x304e/0x54e0 drivers/net/wireless/virtual/mac80211_hwsim.c:5558
init_mac80211_hwsim+0x432/0x8c0 drivers/net/wireless/virtual/mac80211_hwsim.c:6910
do_one_initcall+0x128/0x700 init/main.c:1257
do_initcall_level init/main.c:1319 [inline]
do_initcalls init/main.c:1335 [inline]
do_basic_setup init/main.c:1354 [inline]
kernel_init_freeable+0x5c7/0x900 init/main.c:1568
kernel_init+0x1c/0x2b0 init/main.c:1457
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:148
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
-> #2 (rtnl_mutex){+.+.}-{4:4}:
__mutex_lock_common kernel/locking/mutex.c:585 [inline]
__mutex_lock+0x19b/0xb10 kernel/locking/mutex.c:730
wg_pm_notification drivers/net/wireguard/device.c:80 [inline]
wg_pm_notification+0x49/0x180 drivers/net/wireguard/device.c:64
notifier_call_chain+0xb7/0x410 kernel/notifier.c:85
notifier_call_chain_robust kernel/notifier.c:120 [inline]
blocking_notifier_call_chain_robust kernel/notifier.c:345 [inline]
blocking_notifier_call_chain_robust+0xc9/0x170 kernel/notifier.c:333
pm_notifier_call_chain_robust+0x27/0x60 kernel/power/main.c:102
snapshot_open+0x189/0x2b0 kernel/power/user.c:77
misc_open+0x35a/0x420 drivers/char/misc.c:179
chrdev_open+0x237/0x6a0 fs/char_dev.c:414
do_dentry_open+0x735/0x1c40 fs/open.c:956
vfs_open+0x82/0x3f0 fs/open.c:1086
do_open fs/namei.c:3830 [inline]
path_openat+0x1e88/0x2d80 fs/namei.c:3989
do_filp_open+0x20c/0x470 fs/namei.c:4016
do_sys_openat2+0x17a/0x1e0 fs/open.c:1428
do_sys_open fs/open.c:1443 [inline]
__do_sys_openat fs/open.c:1459 [inline]
__se_sys_openat fs/open.c:1454 [inline]
__x64_sys_openat+0x175/0x210 fs/open.c:1454
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
-> #1 ((pm_chain_head).rwsem){++++}-{4:4}:
down_read+0x9a/0x330 kernel/locking/rwsem.c:1524
blocking_notifier_call_chain_robust kerne
---truncated--- |
