| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
netpoll: Fix race condition in netpoll_owner_active
KCSAN detected a race condition in netpoll:
BUG: KCSAN: data-race in net_rx_action / netpoll_send_skb
write (marked) to 0xffff8881164168b0 of 4 bytes by interrupt on cpu 10:
net_rx_action (./include/linux/netpoll.h:90 net/core/dev.c:6712 net/core/dev.c:6822)
<snip>
read to 0xffff8881164168b0 of 4 bytes by task 1 on cpu 2:
netpoll_send_skb (net/core/netpoll.c:319 net/core/netpoll.c:345 net/core/netpoll.c:393)
netpoll_send_udp (net/core/netpoll.c:?)
<snip>
value changed: 0x0000000a -> 0xffffffff
This happens because netpoll_owner_active() needs to check if the
current CPU is the owner of the lock, touching napi->poll_owner
non atomically. The ->poll_owner field contains the current CPU holding
the lock.
Use an atomic read to check if the poll owner is the current CPU. |
| In the Linux kernel, the following vulnerability has been resolved:
cfg80211: fix race in netlink owner interface destruction
My previous fix here to fix the deadlock left a race where
the exact same deadlock (see the original commit referenced
below) can still happen if cfg80211_destroy_ifaces() already
runs while nl80211_netlink_notify() is still marking some
interfaces as nl_owner_dead.
The race happens because we have two loops here - first we
dev_close() all the netdevs, and then we destroy them. If we
also have two netdevs (first one need only be a wdev though)
then we can find one during the first iteration, close it,
and go to the second iteration -- but then find two, and try
to destroy also the one we didn't close yet.
Fix this by only iterating once. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: Fix race condition during interface enslave
Commit 5dbbbd01cbba83 ("ice: Avoid RTNL lock when re-creating
auxiliary device") changes a process of re-creation of aux device
so ice_plug_aux_dev() is called from ice_service_task() context.
This unfortunately opens a race window that can result in dead-lock
when interface has left LAG and immediately enters LAG again.
Reproducer:
```
#!/bin/sh
ip link add lag0 type bond mode 1 miimon 100
ip link set lag0
for n in {1..10}; do
echo Cycle: $n
ip link set ens7f0 master lag0
sleep 1
ip link set ens7f0 nomaster
done
```
This results in:
[20976.208697] Workqueue: ice ice_service_task [ice]
[20976.213422] Call Trace:
[20976.215871] __schedule+0x2d1/0x830
[20976.219364] schedule+0x35/0xa0
[20976.222510] schedule_preempt_disabled+0xa/0x10
[20976.227043] __mutex_lock.isra.7+0x310/0x420
[20976.235071] enum_all_gids_of_dev_cb+0x1c/0x100 [ib_core]
[20976.251215] ib_enum_roce_netdev+0xa4/0xe0 [ib_core]
[20976.256192] ib_cache_setup_one+0x33/0xa0 [ib_core]
[20976.261079] ib_register_device+0x40d/0x580 [ib_core]
[20976.266139] irdma_ib_register_device+0x129/0x250 [irdma]
[20976.281409] irdma_probe+0x2c1/0x360 [irdma]
[20976.285691] auxiliary_bus_probe+0x45/0x70
[20976.289790] really_probe+0x1f2/0x480
[20976.298509] driver_probe_device+0x49/0xc0
[20976.302609] bus_for_each_drv+0x79/0xc0
[20976.306448] __device_attach+0xdc/0x160
[20976.310286] bus_probe_device+0x9d/0xb0
[20976.314128] device_add+0x43c/0x890
[20976.321287] __auxiliary_device_add+0x43/0x60
[20976.325644] ice_plug_aux_dev+0xb2/0x100 [ice]
[20976.330109] ice_service_task+0xd0c/0xed0 [ice]
[20976.342591] process_one_work+0x1a7/0x360
[20976.350536] worker_thread+0x30/0x390
[20976.358128] kthread+0x10a/0x120
[20976.365547] ret_from_fork+0x1f/0x40
...
[20976.438030] task:ip state:D stack: 0 pid:213658 ppid:213627 flags:0x00004084
[20976.446469] Call Trace:
[20976.448921] __schedule+0x2d1/0x830
[20976.452414] schedule+0x35/0xa0
[20976.455559] schedule_preempt_disabled+0xa/0x10
[20976.460090] __mutex_lock.isra.7+0x310/0x420
[20976.464364] device_del+0x36/0x3c0
[20976.467772] ice_unplug_aux_dev+0x1a/0x40 [ice]
[20976.472313] ice_lag_event_handler+0x2a2/0x520 [ice]
[20976.477288] notifier_call_chain+0x47/0x70
[20976.481386] __netdev_upper_dev_link+0x18b/0x280
[20976.489845] bond_enslave+0xe05/0x1790 [bonding]
[20976.494475] do_setlink+0x336/0xf50
[20976.502517] __rtnl_newlink+0x529/0x8b0
[20976.543441] rtnl_newlink+0x43/0x60
[20976.546934] rtnetlink_rcv_msg+0x2b1/0x360
[20976.559238] netlink_rcv_skb+0x4c/0x120
[20976.563079] netlink_unicast+0x196/0x230
[20976.567005] netlink_sendmsg+0x204/0x3d0
[20976.570930] sock_sendmsg+0x4c/0x50
[20976.574423] ____sys_sendmsg+0x1eb/0x250
[20976.586807] ___sys_sendmsg+0x7c/0xc0
[20976.606353] __sys_sendmsg+0x57/0xa0
[20976.609930] do_syscall_64+0x5b/0x1a0
[20976.613598] entry_SYSCALL_64_after_hwframe+0x65/0xca
1. Command 'ip link ... set nomaster' causes that ice_plug_aux_dev()
is called from ice_service_task() context, aux device is created
and associated device->lock is taken.
2. Command 'ip link ... set master...' calls ice's notifier under
RTNL lock and that notifier calls ice_unplug_aux_dev(). That
function tries to take aux device->lock but this is already taken
by ice_plug_aux_dev() in step 1
3. Later ice_plug_aux_dev() tries to take RTNL lock but this is already
taken in step 2
4. Dead-lock
The patch fixes this issue by following changes:
- Bit ICE_FLAG_PLUG_AUX_DEV is kept to be set during ice_plug_aux_dev()
call in ice_service_task()
- The bit is checked in ice_clear_rdma_cap() and only if it is not set
then ice_unplug_aux_dev() is called. If it is set (in other words
plugging of aux device was requested and ice_plug_aux_dev() is
potentially running) then the function only clears the
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix a race on command flush flow
Fix a refcount use after free warning due to a race on command entry.
Such race occurs when one of the commands releases its last refcount and
frees its index and entry while another process running command flush
flow takes refcount to this command entry. The process which handles
commands flush may see this command as needed to be flushed if the other
process released its refcount but didn't release the index yet. Fix it
by adding the needed spin lock.
It fixes the following warning trace:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 11 PID: 540311 at lib/refcount.c:25 refcount_warn_saturate+0x80/0xe0
...
RIP: 0010:refcount_warn_saturate+0x80/0xe0
...
Call Trace:
<TASK>
mlx5_cmd_trigger_completions+0x293/0x340 [mlx5_core]
mlx5_cmd_flush+0x3a/0xf0 [mlx5_core]
enter_error_state+0x44/0x80 [mlx5_core]
mlx5_fw_fatal_reporter_err_work+0x37/0xe0 [mlx5_core]
process_one_work+0x1be/0x390
worker_thread+0x4d/0x3d0
? rescuer_thread+0x350/0x350
kthread+0x141/0x160
? set_kthread_struct+0x40/0x40
ret_from_fork+0x1f/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: fix kernel panic when enabling bearer
When enabling a bearer on a node, a kernel panic is observed:
[ 4.498085] RIP: 0010:tipc_mon_prep+0x4e/0x130 [tipc]
...
[ 4.520030] Call Trace:
[ 4.520689] <IRQ>
[ 4.521236] tipc_link_build_proto_msg+0x375/0x750 [tipc]
[ 4.522654] tipc_link_build_state_msg+0x48/0xc0 [tipc]
[ 4.524034] __tipc_node_link_up+0xd7/0x290 [tipc]
[ 4.525292] tipc_rcv+0x5da/0x730 [tipc]
[ 4.526346] ? __netif_receive_skb_core+0xb7/0xfc0
[ 4.527601] tipc_l2_rcv_msg+0x5e/0x90 [tipc]
[ 4.528737] __netif_receive_skb_list_core+0x20b/0x260
[ 4.530068] netif_receive_skb_list_internal+0x1bf/0x2e0
[ 4.531450] ? dev_gro_receive+0x4c2/0x680
[ 4.532512] napi_complete_done+0x6f/0x180
[ 4.533570] virtnet_poll+0x29c/0x42e [virtio_net]
...
The node in question is receiving activate messages in another
thread after changing bearer status to allow message sending/
receiving in current thread:
thread 1 | thread 2
-------- | --------
|
tipc_enable_bearer() |
test_and_set_bit_lock() |
tipc_bearer_xmit_skb() |
| tipc_l2_rcv_msg()
| tipc_rcv()
| __tipc_node_link_up()
| tipc_link_build_state_msg()
| tipc_link_build_proto_msg()
| tipc_mon_prep()
| {
| ...
| // null-pointer dereference
| u16 gen = mon->dom_gen;
| ...
| }
// Not being executed yet |
tipc_mon_create() |
{ |
... |
// allocate |
mon = kzalloc(); |
... |
} |
Monitoring pointer in thread 2 is dereferenced before monitoring data
is allocated in thread 1. This causes kernel panic.
This commit fixes it by allocating the monitoring data before enabling
the bearer to receive messages. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: scrub: handle RST lookup error correctly
[BUG]
When running btrfs/060 with forced RST feature, it would crash the
following ASSERT() inside scrub_read_endio():
ASSERT(sector_nr < stripe->nr_sectors);
Before that, we would have tree dump from
btrfs_get_raid_extent_offset(), as we failed to find the RST entry for
the range.
[CAUSE]
Inside scrub_submit_extent_sector_read() every time we allocated a new
bbio we immediately called btrfs_map_block() to make sure there was some
RST range covering the scrub target.
But if btrfs_map_block() fails, we immediately call endio for the bbio,
while the bbio is newly allocated, it's completely empty.
Then inside scrub_read_endio(), we go through the bvecs to find
the sector number (as bi_sector is no longer reliable if the bio is
submitted to lower layers).
And since the bio is empty, such bvecs iteration would not find any
sector matching the sector, and return sector_nr == stripe->nr_sectors,
triggering the ASSERT().
[FIX]
Instead of calling btrfs_map_block() after allocating a new bbio, call
btrfs_map_block() first.
Since our only objective of calling btrfs_map_block() is only to update
stripe_len, there is really no need to do that after btrfs_alloc_bio().
This new timing would avoid the problem of handling empty bbio
completely, and in fact fixes a possible race window for the old code,
where if the submission thread is the only owner of the pending_io, the
scrub would never finish (since we didn't decrease the pending_io
counter).
Although the root cause of RST lookup failure still needs to be
addressed. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix race condition between session lookup and expire
Thread A + Thread B
ksmbd_session_lookup | smb2_sess_setup
sess = xa_load |
|
| xa_erase(&conn->sessions, sess->id);
|
| ksmbd_session_destroy(sess) --> kfree(sess)
|
// UAF! |
sess->last_active = jiffies |
+
This patch add rwsem to fix race condition between ksmbd_session_lookup
and ksmbd_expire_session. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: compress: fix race condition of overwrite vs truncate
pos_fsstress testcase complains a panic as belew:
------------[ cut here ]------------
kernel BUG at fs/f2fs/compress.c:1082!
invalid opcode: 0000 [#1] SMP PTI
CPU: 4 PID: 2753477 Comm: kworker/u16:2 Tainted: G OE 5.12.0-rc1-custom #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
Workqueue: writeback wb_workfn (flush-252:16)
RIP: 0010:prepare_compress_overwrite+0x4c0/0x760 [f2fs]
Call Trace:
f2fs_prepare_compress_overwrite+0x5f/0x80 [f2fs]
f2fs_write_cache_pages+0x468/0x8a0 [f2fs]
f2fs_write_data_pages+0x2a4/0x2f0 [f2fs]
do_writepages+0x38/0xc0
__writeback_single_inode+0x44/0x2a0
writeback_sb_inodes+0x223/0x4d0
__writeback_inodes_wb+0x56/0xf0
wb_writeback+0x1dd/0x290
wb_workfn+0x309/0x500
process_one_work+0x220/0x3c0
worker_thread+0x53/0x420
kthread+0x12f/0x150
ret_from_fork+0x22/0x30
The root cause is truncate() may race with overwrite as below,
so that one reference count left in page can not guarantee the
page attaching in mapping tree all the time, after truncation,
later find_lock_page() may return NULL pointer.
- prepare_compress_overwrite
- f2fs_pagecache_get_page
- unlock_page
- f2fs_setattr
- truncate_setsize
- truncate_inode_page
- delete_from_page_cache
- find_lock_page
Fix this by avoiding referencing updated page. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: sun6i: fix race between DMA RX transfer completion and RX FIFO drain
Previously the transfer complete IRQ immediately drained to RX FIFO to
read any data remaining in FIFO to the RX buffer. This behaviour is
correct when dealing with SPI in interrupt mode. However in DMA mode the
transfer complete interrupt still fires as soon as all bytes to be
transferred have been stored in the FIFO. At that point data in the FIFO
still needs to be picked up by the DMA engine. Thus the drain procedure
and DMA engine end up racing to read from RX FIFO, corrupting any data
read. Additionally the RX buffer pointer is never adjusted according to
DMA progress in DMA mode, thus calling the RX FIFO drain procedure in DMA
mode is a bug.
Fix corruptions in DMA RX mode by draining RX FIFO only in interrupt mode.
Also wait for completion of RX DMA when in DMA mode before returning to
ensure all data has been copied to the supplied memory buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/cio: fix race condition during online processing
A race condition exists in ccw_device_set_online() that can cause the
online process to fail, leaving the affected device in an inconsistent
state. As a result, subsequent attempts to set that device online fail
with return code ENODEV.
The problem occurs when a path verification request arrives after
a wait for final device state completed, but before the result state
is evaluated.
Fix this by ensuring that the CCW-device lock is held between
determining final state and checking result state.
Note that since:
commit 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers")
path verification requests are much more likely to occur during boot,
resulting in an increased chance of this race condition occurring. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: fix IO hang from sbitmap wakeup race
In blk_mq_mark_tag_wait(), __add_wait_queue() may be re-ordered
with the following blk_mq_get_driver_tag() in case of getting driver
tag failure.
Then in __sbitmap_queue_wake_up(), waitqueue_active() may not observe
the added waiter in blk_mq_mark_tag_wait() and wake up nothing, meantime
blk_mq_mark_tag_wait() can't get driver tag successfully.
This issue can be reproduced by running the following test in loop, and
fio hang can be observed in < 30min when running it on my test VM
in laptop.
modprobe -r scsi_debug
modprobe scsi_debug delay=0 dev_size_mb=4096 max_queue=1 host_max_queue=1 submit_queues=4
dev=`ls -d /sys/bus/pseudo/drivers/scsi_debug/adapter*/host*/target*/*/block/* | head -1 | xargs basename`
fio --filename=/dev/"$dev" --direct=1 --rw=randrw --bs=4k --iodepth=1 \
--runtime=100 --numjobs=40 --time_based --name=test \
--ioengine=libaio
Fix the issue by adding one explicit barrier in blk_mq_mark_tag_wait(), which
is just fine in case of running out of tag. |
| In the Linux kernel, the following vulnerability has been resolved:
Fix page corruption caused by racy check in __free_pages
When we upgraded our kernel, we started seeing some page corruption like
the following consistently:
BUG: Bad page state in process ganesha.nfsd pfn:1304ca
page:0000000022261c55 refcount:0 mapcount:-128 mapping:0000000000000000 index:0x0 pfn:0x1304ca
flags: 0x17ffffc0000000()
raw: 0017ffffc0000000 ffff8a513ffd4c98 ffffeee24b35ec08 0000000000000000
raw: 0000000000000000 0000000000000001 00000000ffffff7f 0000000000000000
page dumped because: nonzero mapcount
CPU: 0 PID: 15567 Comm: ganesha.nfsd Kdump: loaded Tainted: P B O 5.10.158-1.nutanix.20221209.el7.x86_64 #1
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/05/2016
Call Trace:
dump_stack+0x74/0x96
bad_page.cold+0x63/0x94
check_new_page_bad+0x6d/0x80
rmqueue+0x46e/0x970
get_page_from_freelist+0xcb/0x3f0
? _cond_resched+0x19/0x40
__alloc_pages_nodemask+0x164/0x300
alloc_pages_current+0x87/0xf0
skb_page_frag_refill+0x84/0x110
...
Sometimes, it would also show up as corruption in the free list pointer
and cause crashes.
After bisecting the issue, we found the issue started from commit
e320d3012d25 ("mm/page_alloc.c: fix freeing non-compound pages"):
if (put_page_testzero(page))
free_the_page(page, order);
else if (!PageHead(page))
while (order-- > 0)
free_the_page(page + (1 << order), order);
So the problem is the check PageHead is racy because at this point we
already dropped our reference to the page. So even if we came in with
compound page, the page can already be freed and PageHead can return
false and we will end up freeing all the tail pages causing double free. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: vsie: fix race during shadow creation
Right now it is possible to see gmap->private being zero in
kvm_s390_vsie_gmap_notifier resulting in a crash. This is due to the
fact that we add gmap->private == kvm after creation:
static int acquire_gmap_shadow(struct kvm_vcpu *vcpu,
struct vsie_page *vsie_page)
{
[...]
gmap = gmap_shadow(vcpu->arch.gmap, asce, edat);
if (IS_ERR(gmap))
return PTR_ERR(gmap);
gmap->private = vcpu->kvm;
Let children inherit the private field of the parent. |
| In the Linux kernel, the following vulnerability has been resolved:
xen/events: close evtchn after mapping cleanup
shutdown_pirq and startup_pirq are not taking the
irq_mapping_update_lock because they can't due to lock inversion. Both
are called with the irq_desc->lock being taking. The lock order,
however, is first irq_mapping_update_lock and then irq_desc->lock.
This opens multiple races:
- shutdown_pirq can be interrupted by a function that allocates an event
channel:
CPU0 CPU1
shutdown_pirq {
xen_evtchn_close(e)
__startup_pirq {
EVTCHNOP_bind_pirq
-> returns just freed evtchn e
set_evtchn_to_irq(e, irq)
}
xen_irq_info_cleanup() {
set_evtchn_to_irq(e, -1)
}
}
Assume here event channel e refers here to the same event channel
number.
After this race the evtchn_to_irq mapping for e is invalid (-1).
- __startup_pirq races with __unbind_from_irq in a similar way. Because
__startup_pirq doesn't take irq_mapping_update_lock it can grab the
evtchn that __unbind_from_irq is currently freeing and cleaning up. In
this case even though the event channel is allocated, its mapping can
be unset in evtchn_to_irq.
The fix is to first cleanup the mappings and then close the event
channel. In this way, when an event channel gets allocated it's
potential previous evtchn_to_irq mappings are guaranteed to be unset already.
This is also the reverse order of the allocation where first the event
channel is allocated and then the mappings are setup.
On a 5.10 kernel prior to commit 3fcdaf3d7634 ("xen/events: modify internal
[un]bind interfaces"), we hit a BUG like the following during probing of NVMe
devices. The issue is that during nvme_setup_io_queues, pci_free_irq
is called for every device which results in a call to shutdown_pirq.
With many nvme devices it's therefore likely to hit this race during
boot because there will be multiple calls to shutdown_pirq and
startup_pirq are running potentially in parallel.
------------[ cut here ]------------
blkfront: xvda: barrier or flush: disabled; persistent grants: enabled; indirect descriptors: enabled; bounce buffer: enabled
kernel BUG at drivers/xen/events/events_base.c:499!
invalid opcode: 0000 [#1] SMP PTI
CPU: 44 PID: 375 Comm: kworker/u257:23 Not tainted 5.10.201-191.748.amzn2.x86_64 #1
Hardware name: Xen HVM domU, BIOS 4.11.amazon 08/24/2006
Workqueue: nvme-reset-wq nvme_reset_work
RIP: 0010:bind_evtchn_to_cpu+0xdf/0xf0
Code: 5d 41 5e c3 cc cc cc cc 44 89 f7 e8 2b 55 ad ff 49 89 c5 48 85 c0 0f 84 64 ff ff ff 4c 8b 68 30 41 83 fe ff 0f 85 60 ff ff ff <0f> 0b 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 0f 1f 44 00 00
RSP: 0000:ffffc9000d533b08 EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000006
RDX: 0000000000000028 RSI: 00000000ffffffff RDI: 00000000ffffffff
RBP: ffff888107419680 R08: 0000000000000000 R09: ffffffff82d72b00
R10: 0000000000000000 R11: 0000000000000000 R12: 00000000000001ed
R13: 0000000000000000 R14: 00000000ffffffff R15: 0000000000000002
FS: 0000000000000000(0000) GS:ffff88bc8b500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000002610001 CR4: 00000000001706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
? show_trace_log_lvl+0x1c1/0x2d9
? show_trace_log_lvl+0x1c1/0x2d9
? set_affinity_irq+0xdc/0x1c0
? __die_body.cold+0x8/0xd
? die+0x2b/0x50
? do_trap+0x90/0x110
? bind_evtchn_to_cpu+0xdf/0xf0
? do_error_trap+0x65/0x80
? bind_evtchn_to_cpu+0xdf/0xf0
? exc_invalid_op+0x4e/0x70
? bind_evtchn_to_cpu+0xdf/0xf0
? asm_exc_invalid_op+0x12/0x20
? bind_evtchn_to_cpu+0xdf/0x
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dpu: Add mutex lock in control vblank irq
Add a mutex lock to control vblank irq to synchronize vblank
enable/disable operations happening from different threads to prevent
race conditions while registering/unregistering the vblank irq callback.
v4: -Removed vblank_ctl_lock from dpu_encoder_virt, so it is only a
parameter of dpu_encoder_phys.
-Switch from atomic refcnt to a simple int counter as mutex has
now been added
v3: Mistakenly did not change wording in last version. It is done now.
v2: Slightly changed wording of commit message
Patchwork: https://patchwork.freedesktop.org/patch/571854/ |
| In the Linux kernel, the following vulnerability has been resolved:
wireguard: receive: annotate data-race around receiving_counter.counter
Syzkaller with KCSAN identified a data-race issue when accessing
keypair->receiving_counter.counter. Use READ_ONCE() and WRITE_ONCE()
annotations to mark the data race as intentional.
BUG: KCSAN: data-race in wg_packet_decrypt_worker / wg_packet_rx_poll
write to 0xffff888107765888 of 8 bytes by interrupt on cpu 0:
counter_validate drivers/net/wireguard/receive.c:321 [inline]
wg_packet_rx_poll+0x3ac/0xf00 drivers/net/wireguard/receive.c:461
__napi_poll+0x60/0x3b0 net/core/dev.c:6536
napi_poll net/core/dev.c:6605 [inline]
net_rx_action+0x32b/0x750 net/core/dev.c:6738
__do_softirq+0xc4/0x279 kernel/softirq.c:553
do_softirq+0x5e/0x90 kernel/softirq.c:454
__local_bh_enable_ip+0x64/0x70 kernel/softirq.c:381
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
_raw_spin_unlock_bh+0x36/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:396 [inline]
ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
wg_packet_decrypt_worker+0x6c5/0x700 drivers/net/wireguard/receive.c:499
process_one_work kernel/workqueue.c:2633 [inline]
...
read to 0xffff888107765888 of 8 bytes by task 3196 on cpu 1:
decrypt_packet drivers/net/wireguard/receive.c:252 [inline]
wg_packet_decrypt_worker+0x220/0x700 drivers/net/wireguard/receive.c:501
process_one_work kernel/workqueue.c:2633 [inline]
process_scheduled_works+0x5b8/0xa30 kernel/workqueue.c:2706
worker_thread+0x525/0x730 kernel/workqueue.c:2787
... |
| In the Linux kernel, the following vulnerability has been resolved:
quota: Fix potential NULL pointer dereference
Below race may cause NULL pointer dereference
P1 P2
dquot_free_inode quota_off
drop_dquot_ref
remove_dquot_ref
dquots = i_dquot(inode)
dquots = i_dquot(inode)
srcu_read_lock
dquots[cnt]) != NULL (1)
dquots[type] = NULL (2)
spin_lock(&dquots[cnt]->dq_dqb_lock) (3)
....
If dquot_free_inode(or other routines) checks inode's quota pointers (1)
before quota_off sets it to NULL(2) and use it (3) after that, NULL pointer
dereference will be triggered.
So let's fix it by using a temporary pointer to avoid this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: delay all of ath9k_wmi_event_tasklet() until init is complete
The ath9k_wmi_event_tasklet() used in ath9k_htc assumes that all the data
structures have been fully initialised by the time it runs. However, because of
the order in which things are initialised, this is not guaranteed to be the
case, because the device is exposed to the USB subsystem before the ath9k driver
initialisation is completed.
We already committed a partial fix for this in commit:
8b3046abc99e ("ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()")
However, that commit only aborted the WMI_TXSTATUS_EVENTID command in the event
tasklet, pairing it with an "initialisation complete" bit in the TX struct. It
seems syzbot managed to trigger the race for one of the other commands as well,
so let's just move the existing synchronisation bit to cover the whole
tasklet (setting it at the end of ath9k_htc_probe_device() instead of inside
ath9k_tx_init()). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Fix ufshcd_abort_one racing issue
When ufshcd_abort_one is racing with the completion ISR, the completed tag
of the request's mq_hctx pointer will be set to NULL by ISR. Return
success when request is completed by ISR because ufshcd_abort_one does not
need to do anything.
The racing flow is:
Thread A
ufshcd_err_handler step 1
...
ufshcd_abort_one
ufshcd_try_to_abort_task
ufshcd_cmd_inflight(true) step 3
ufshcd_mcq_req_to_hwq
blk_mq_unique_tag
rq->mq_hctx->queue_num step 5
Thread B
ufs_mtk_mcq_intr(cq complete ISR) step 2
scsi_done
...
__blk_mq_free_request
rq->mq_hctx = NULL; step 4
Below is KE back trace.
ufshcd_try_to_abort_task: cmd at tag 41 not pending in the device.
ufshcd_try_to_abort_task: cmd at tag=41 is cleared.
Aborting tag 41 / CDB 0x28 succeeded
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000194
pc : [0xffffffddd7a79bf8] blk_mq_unique_tag+0x8/0x14
lr : [0xffffffddd6155b84] ufshcd_mcq_req_to_hwq+0x1c/0x40 [ufs_mediatek_mod_ise]
do_mem_abort+0x58/0x118
el1_abort+0x3c/0x5c
el1h_64_sync_handler+0x54/0x90
el1h_64_sync+0x68/0x6c
blk_mq_unique_tag+0x8/0x14
ufshcd_err_handler+0xae4/0xfa8 [ufs_mediatek_mod_ise]
process_one_work+0x208/0x4fc
worker_thread+0x228/0x438
kthread+0x104/0x1d4
ret_from_fork+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Fix ufshcd_clear_cmd racing issue
When ufshcd_clear_cmd is racing with the completion ISR, the completed tag
of the request's mq_hctx pointer will be set to NULL by the ISR. And
ufshcd_clear_cmd's call to ufshcd_mcq_req_to_hwq will get NULL pointer KE.
Return success when the request is completed by ISR because sq does not
need cleanup.
The racing flow is:
Thread A
ufshcd_err_handler step 1
ufshcd_try_to_abort_task
ufshcd_cmd_inflight(true) step 3
ufshcd_clear_cmd
...
ufshcd_mcq_req_to_hwq
blk_mq_unique_tag
rq->mq_hctx->queue_num step 5
Thread B
ufs_mtk_mcq_intr(cq complete ISR) step 2
scsi_done
...
__blk_mq_free_request
rq->mq_hctx = NULL; step 4
Below is KE back trace:
ufshcd_try_to_abort_task: cmd pending in the device. tag = 6
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000194
pc : [0xffffffd589679bf8] blk_mq_unique_tag+0x8/0x14
lr : [0xffffffd5862f95b4] ufshcd_mcq_sq_cleanup+0x6c/0x1cc [ufs_mediatek_mod_ise]
Workqueue: ufs_eh_wq_0 ufshcd_err_handler [ufs_mediatek_mod_ise]
Call trace:
dump_backtrace+0xf8/0x148
show_stack+0x18/0x24
dump_stack_lvl+0x60/0x7c
dump_stack+0x18/0x3c
mrdump_common_die+0x24c/0x398 [mrdump]
ipanic_die+0x20/0x34 [mrdump]
notify_die+0x80/0xd8
die+0x94/0x2b8
__do_kernel_fault+0x264/0x298
do_page_fault+0xa4/0x4b8
do_translation_fault+0x38/0x54
do_mem_abort+0x58/0x118
el1_abort+0x3c/0x5c
el1h_64_sync_handler+0x54/0x90
el1h_64_sync+0x68/0x6c
blk_mq_unique_tag+0x8/0x14
ufshcd_clear_cmd+0x34/0x118 [ufs_mediatek_mod_ise]
ufshcd_try_to_abort_task+0x2c8/0x5b4 [ufs_mediatek_mod_ise]
ufshcd_err_handler+0xa7c/0xfa8 [ufs_mediatek_mod_ise]
process_one_work+0x208/0x4fc
worker_thread+0x228/0x438
kthread+0x104/0x1d4
ret_from_fork+0x10/0x20 |
