| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: fix use-after-free in store_modes()
store_modes() replaces a framebuffer's modelist with modes from userspace.
On success it frees the old modelist with fb_destroy_modelist(). Two
fields still point into that freed list.
One pointer is fb_display[i].mode, the mode a console is using.
fbcon_new_modelist() moves these pointers to the new list. It only does so
for consoles still mapped to the framebuffer. An unmapped console is
skipped and keeps its stale pointer. Unbinding fbcon, for example, sets
con2fb_map[i] to -1 but leaves fb_display[i].mode set. An
FBIOPUT_VSCREENINFO ioctl with FB_ACTIVATE_INV_MODE later reaches
fbcon_mode_deleted(). That function reads the stale fb_display[i].mode
through fb_mode_is_equal(). The read is a use-after-free.
The other pointer is fb_info->mode, the current mode. It is set through
the mode sysfs attribute. store_modes() does not update fb_info->mode, so
it is left pointing into the freed list. show_mode(), the attribute's read
handler, dereferences the stale fb_info->mode through mode_string(). The
read is a use-after-free.
Clear both pointers before freeing the list. Commit a1f305893074 ("fbcon:
Set fb_display[i]->mode to NULL when the mode is released") added the
helper fbcon_delete_modelist(). It clears every fb_display[i].mode that
points into a given list. So far it is called only from the unregister
path. Call it from store_modes() too, and set fb_info->mode to NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
gcov: use atomic counter updates to fix concurrent access crashes
GCC's GCOV instrumentation can merge global branch counters with loop
induction variables as an optimization. In inflate_fast(), the inner copy
loops get transformed so that the GCOV counter value is loaded multiple
times to compute the loop base address, start index, and end bound. Since
GCOV counters are global (not per-CPU), concurrent execution on different
CPUs causes the counter to change between loads, producing inconsistent
values and out-of-bounds memory writes.
The crash manifests during IPComp (IP Payload Compression) processing when
inflate_fast() runs concurrently on multiple CPUs:
BUG: unable to handle page fault for address: ffffd0a3c0902ffa
RIP: inflate_fast+1431
Call Trace:
zlib_inflate
__deflate_decompress
crypto_comp_decompress
ipcomp_decompress [xfrm_ipcomp]
ipcomp_input [xfrm_ipcomp]
xfrm_input
At the crash point, the compiler generated three loads from the same
global GCOV counter (__gcov0.inflate_fast+216) to compute base, start, and
end for an indexed loop. Another CPU modified the counter between loads,
making the values inconsistent - the write went 3.4 MB past a 65 KB
buffer.
Add -fprofile-update=prefer-atomic to CFLAGS_GCOV at the global level in
the top-level Makefile, guarded by a try-run compile test. The test
compiles a minimal program with and without -fprofile-update=prefer-atomic
using the full KBUILD_CFLAGS, then compares undefined symbols in the
resulting object files. If prefer-atomic introduces new undefined
references (such as __atomic_fetch_add_8 on i386 or __aarch64_ldadd8_relax
on arm64 with outline-atomics), the flag is not added -- the kernel does
not link against libatomic.
On architectures where GCC inlines 64-bit atomic counter updates (x86_64,
s390, ...) the test passes and the flag is enabled, preventing the
compiler from merging counters with loop induction variables and fixing
the observed concurrent-access crash.
On architectures where the flag would introduce libatomic dependencies, it
is silently omitted and behaviour is no worse than before this patch.
Move the CFLAGS_GCOV block from its original position (before the arch
Makefile include) to after the core KBUILD_CFLAGS assignments but before
the scripts/Makefile.gcc-plugins include. This placement ensures the
try-run test sees arch-specific flags (-m32, -march=,
-mno-outline-atomics) while avoiding GCC plugin flags (-fplugin=) that
would break the test on clean builds when plugin shared objects do not yet
exist. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: omap2: fix use-after-free in omapfb_mmap
omapfb_mmap() has a race condition with OMAPFB_SETUP_PLANE ioctl that
can lead to use-after-free:
The fb_mmap() entry point holds mm_lock but not lock (fb_info->lock),
while ioctl handlers like OMAPFB_SETUP_PLANE hold lock but not mm_lock.
This allows concurrent execution.
In omapfb_mmap():
1. rg = omapfb_get_mem_region(ofbi->region); // Get old region ref
2. start = omapfb_get_region_paddr(ofbi); // Read from NEW region
3. len = fix->smem_len; // Read from NEW region
4. vm_iomap_memory(vma, start, len); // Map NEW region memory
5. atomic_inc(&rg->map_count); // Increment OLD region!
Concurrently, OMAPFB_SETUP_PLANE can:
- Reassign ofbi->region = new_rg
- Update fix->smem_len
- OMAPFB_SETUP_MEM then checks NEW region's map_count (0!) and frees it
This leaves userspace with a mapping to freed physical memory.
The fix is to read all required values (start, len) from the same
region reference (rg) that will have its map_count incremented,
preventing the region from being freed while still mapped. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: always recover the gpu
Previously, in case there was no more work to do, recover worker
wouldn't trigger recovery and would instead rely on the gpu going to
sleep and then resuming when more work is submitted.
Recover_worker will first increment the fence of the hung ring so, if
there's only one job submitted to a ring and that causes an hang, it
will early out.
There's no guarantee that the gpu will suspend and resume before more
work is submitted and if the gpu is in a hung state it will stay in that
state and probably trigger a timeout again.
Just stop checking and always recover the gpu.
Patchwork: https://patchwork.freedesktop.org/patch/704066/ |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Add upper bound check for num_of_nodes
drm/amdkfd: Add upper bound check for num_of_nodes
in kfd_ioctl_get_process_apertures_new.
(cherry picked from commit 98ff46a5ea090c14d2cdb4f5b993b05d74f3949f) |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix fsck inconsistency caused by incorrect nat_entry flag usage
f2fs_need_dentry_mark() reads nat_entry flags without mutual exclusion
with the checkpoint path, which can result in an incorrect inode block
marking state. The scenario is as follows:
create & write & fsync 'file A' write checkpoint
- f2fs_do_sync_file // inline inode
- f2fs_write_inode // inode folio is dirty
- f2fs_write_checkpoint
- f2fs_flush_merged_writes
- f2fs_sync_node_pages
- f2fs_fsync_node_pages // no dirty node
- f2fs_need_inode_block_update // return true
- f2fs_fsync_node_pages // inode dirtied
- f2fs_need_dentry_mark //return true
- f2fs_flush_nat_entries
- f2fs_write_checkpoint end
- __write_node_folio // inode with DENT_BIT_SHIFT set
SPO, "fsck --dry-run" find inode has already checkpointed but still
with DENT_BIT_SHIFT set
The state observed by f2fs_need_dentry_mark() can differ from the state
observed in __write_node_folio() after acquiring sbi->node_write. The
root cause is that the semantics of IS_CHECKPOINTED and
HAS_FSYNCED_INODE are only guaranteed after the checkpoint write has
fully completed.
This patch moves set_dentry_mark() into __write_node_folio() and
protects it with the sbi->node_write lock. |
| In the Linux kernel, the following vulnerability has been resolved:
hsr: Remove WARN_ONCE() in hsr_addr_is_self().
syzbot reported the warning [0] in hsr_addr_is_self(),
whose assumption is simply wrong.
hsr->self_node is cleared in hsr_del_self_node(), which
is called from hsr_dellink().
Since dev->rtnl_link_ops->dellink() is called before
unregister_netdevice_many(), there is a window when
user can find the device but without hsr->self_node.
Let's remove WARN_ONCE() in hsr_addr_is_self().
[0]:
HSR: No self node
WARNING: net/hsr/hsr_framereg.c:39 at hsr_addr_is_self+0x211/0x3f0 net/hsr/hsr_framereg.c:39, CPU#0: syz.4.16848/17220
Modules linked in:
CPU: 0 UID: 0 PID: 17220 Comm: syz.4.16848 Tainted: G L syzkaller #0 PREEMPT_{RT,(full)}
Tainted: [L]=SOFTLOCKUP
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/18/2026
RIP: 0010:hsr_addr_is_self+0x211/0x3f0 net/hsr/hsr_framereg.c:39
Code: 33 2f 41 0f b7 dd 89 ee 09 de 31 ff e8 c8 b4 c6 f6 09 dd 74 54 e8 0f b0 c6 f6 31 ed eb 53 e8 06 b0 c6 f6 48 8d 3d 2f 50 9c 04 <67> 48 0f b9 3a 31 ed eb 42 e8 c1 13 1f 00 89 c5 31 ff 89 c6 e8 96
RSP: 0018:ffffc900041c70e0 EFLAGS: 00010283
RAX: ffffffff8afdc6ca RBX: ffffffff8afdc4e6 RCX: 0000000000080000
RDX: ffffc90010493000 RSI: 0000000000000948 RDI: ffffffff8f9a1700
RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
R10: ffffc900041c71e8 R11: fffff52000838e3f R12: dffffc0000000000
R13: ffff888041f9e3c0 R14: ffff888086ee3802 R15: 0000000000000000
FS: 00007f6fe985d6c0(0000) GS:ffff888126176000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f80bd437dac CR3: 0000000025096000 CR4: 00000000003526f0
DR0: ffffffffffffffff DR1: 00000000000001f8 DR2: 0000000000000002
DR3: ffffffffefffff15 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
check_local_dest net/hsr/hsr_forward.c:592 [inline]
fill_frame_info net/hsr/hsr_forward.c:728 [inline]
hsr_forward_skb+0xa11/0x2a80 net/hsr/hsr_forward.c:739
hsr_dev_xmit+0x253/0x370 net/hsr/hsr_device.c:236
__netdev_start_xmit include/linux/netdevice.h:5368 [inline]
netdev_start_xmit include/linux/netdevice.h:5377 [inline]
xmit_one net/core/dev.c:3888 [inline]
dev_hard_start_xmit+0x2df/0x860 net/core/dev.c:3904
__dev_queue_xmit+0x1428/0x3900 net/core/dev.c:4870
neigh_output include/net/neighbour.h:556 [inline]
ip_finish_output2+0xcec/0x10b0 net/ipv4/ip_output.c:237
ip_send_skb net/ipv4/ip_output.c:1510 [inline]
ip_push_pending_frames+0x8b/0x110 net/ipv4/ip_output.c:1530
raw_sendmsg+0x1547/0x1a50 net/ipv4/raw.c:659
sock_sendmsg_nosec net/socket.c:787 [inline]
__sock_sendmsg net/socket.c:802 [inline]
____sys_sendmsg+0x7da/0x9c0 net/socket.c:2698
___sys_sendmsg+0x2a5/0x360 net/socket.c:2752
__sys_sendmsg net/socket.c:2784 [inline]
__do_sys_sendmsg net/socket.c:2789 [inline]
__se_sys_sendmsg net/socket.c:2787 [inline]
__x64_sys_sendmsg+0x1c3/0x2a0 net/socket.c:2787
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x15f/0xf80 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f6feb62ce59
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f6fe985d028 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f6feb8a6090 RCX: 00007f6feb62ce59
RDX: 0000000000000000 RSI: 0000200000000000 RDI: 0000000000000004
RBP: 00007f6feb6c2d6f R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007f6feb8a6128 R14: 00007f6feb8a6090 R15: 00007ffcf01cc488
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: Don't WARN if memory is dirtied without a vCPU when the VM is dying
When marking a page dirty, complain about not having a running/loaded vCPU
if and only if the VM is still alive, i.e. its refcount is non-zero. This
will allow fixing a memory leak for x86 SEV-ES guests without hitting what
is effectively a false positive on the WARN.
For some SEV-ES VM-Exits, KVM keeps a writable mapping of a guest page
across an exit to userspace, and typically unmaps the page on the next
KVM_RUN. But if userspace never calls KVM_RUN after such an exit, then KVM
needs to unmap the page when the vCPU is destroyed, which in turn triggers
the WARN about not having a running vCPU.
Alternatively, SEV-ES could temporarily load the vCPU to suppress the WARN,
as is done in nested_vmx_free_vcpu() (but for completely unrelated reasons;
suppressing WARN from nested_put_vmcs12_pages() is pure happenstance). But
loading a vCPU during destruction is gross (ideally nVMX code would be
cleaned up), risks complicating the SEV-ES code (KVM would need to ensure
the temporarily load()+put() only runs when the vCPU isn't already loaded),
and is ultimately pointless.
The motivation for the WARN is to guard against KVM dirtying guest memory
without pushing the corresponding GFN to the active vCPU's dirty ring, e.g.
to ensure userspace doesn't miss a dirty page. But for the VM's refcount
to reach zero, there can't be _any_ userspace mappings to the dirty ring,
as mapping the dirty ring requires doing mmap() on the vCPU FD. I.e. if
userspace had a valid mapping for the dirty ring, then the vCPU file and
thus the owning VM would still be alive. And so since userspace can't
possibly reach the dirty ring, whether or not KVM technically "misses" a
push to the dirty ring is irrelevant. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix out-of-bounds read in dp_get_eq_aux_rd_interval()
[Why & How]
The aux_rd_interval array in struct dc_lttpr_caps is declared with
MAX_REPEATER_CNT - 1 (7) elements, indexed 0..6. However, the offset
parameter passed to dp_get_eq_aux_rd_interval() can be as large as
MAX_REPEATER_CNT (8) when a sink reports 8 LTTPR repeaters via DPCD.
This leads to an out-of-bounds read of aux_rd_interval[7] when offset
is 8.
Fix this by growing aux_rd_interval to MAX_REPEATER_CNT elements to
accommodate the full range of valid repeater counts defined by the DP
spec.
(cherry picked from commit a55a458a8df37a65ffda5cf721d554a8f74f6b04) |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: Place upper limit on station AID
Any station configured with an AID over 20 causes a firmware crash.
This situation occurred in our testing using an AP interface on 7922
hardware, with a modified hostapd, sourced from Mediatek's OpenWRT
feeds.
In stock hostapd, station AIDs begin counting at 1, and this
configuration is prevented with an upper limit on associated stations.
However, the modified hostapd began allocation at 65, which caused the
firmware to crash. This fix does not allow these AIDs to work, but will
prevent the firmware crash.
This crash was only seen on IFTYPE_AP interfaces, and the fix does not
appear to have an effect on IFTYPE_STATION behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Avoid NULL dereference in dc_dmub_srv error paths
In dc_dmub_srv_log_diagnostic_data() and
dc_dmub_srv_enable_dpia_trace().
Both functions check:
if (!dc_dmub_srv || !dc_dmub_srv->dmub)
and then call DC_LOG_ERROR() inside that block.
DC_LOG_ERROR() uses dc_dmub_srv->ctx internally. So if
dc_dmub_srv is NULL, the logging itself can dereference a
NULL pointer and cause a crash.
Fix this by splitting the checks.
First check if dc_dmub_srv is NULL and return immediately.
Then check dc_dmub_srv->dmub and log the error only when
dc_dmub_srv is valid.
Fixes the below:
../display/dc/dc_dmub_srv.c:962 dc_dmub_srv_log_diagnostic_data() error: we previously assumed 'dc_dmub_srv' could be null (see line 961)
../display/dc/dc_dmub_srv.c:1167 dc_dmub_srv_enable_dpia_trace() error: we previously assumed 'dc_dmub_srv' could be null (see line 1166) |
| In the Linux kernel, the following vulnerability has been resolved:
net: mana: Guard mana_remove against double invocation
If PM resume fails (e.g., mana_attach() returns an error), mana_probe()
calls mana_remove(), which tears down the device and sets
gd->gdma_context = NULL and gd->driver_data = NULL.
However, a failed resume callback does not automatically unbind the
driver. When the device is eventually unbound, mana_remove() is invoked
a second time. Without a NULL check, it dereferences gc->dev with
gc == NULL, causing a kernel panic.
Add an early return if gdma_context or driver_data is NULL so the second
invocation is harmless. Move the dev = gc->dev assignment after the
guard so it cannot dereference NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phonet: do not BUG_ON() in pn_socket_autobind() on failed bind
syzbot reported a kernel BUG triggered from pn_socket_sendmsg() via
pn_socket_autobind():
kernel BUG at net/phonet/socket.c:213!
RIP: 0010:pn_socket_autobind net/phonet/socket.c:213 [inline]
RIP: 0010:pn_socket_sendmsg+0x240/0x250 net/phonet/socket.c:421
Call Trace:
sock_sendmsg_nosec+0x112/0x150 net/socket.c:797
__sock_sendmsg net/socket.c:812 [inline]
__sys_sendto+0x402/0x590 net/socket.c:2280
...
pn_socket_autobind() calls pn_socket_bind() with port 0 and, on
-EINVAL, assumes the socket was already bound and asserts that the
port is non-zero:
err = pn_socket_bind(sock, ..., sizeof(struct sockaddr_pn));
if (err != -EINVAL)
return err;
BUG_ON(!pn_port(pn_sk(sock->sk)->sobject));
return 0; /* socket was already bound */
However pn_socket_bind() also returns -EINVAL when sk->sk_state is not
TCP_CLOSE, even when the socket has never been bound and pn_port() is
still 0. In that case the BUG_ON() fires and panics the kernel from a
user-triggerable path.
Treat the "bind returned -EINVAL but pn_port() is still 0" case as a
regular error and propagate -EINVAL to the caller instead of crashing.
Existing callers already translate a non-zero return from
pn_socket_autobind() into -ENOBUFS/-EAGAIN, so returning -EINVAL here
only changes behaviour from panic to a normal errno. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: only release the dirty pages io tree after successful writes
[WARNING]
With extra warning on dirty extent buffers at umount (aka, the next
patch in the series), test case generic/388 can trigger the following
warning about dirty extent buffers at unmount time:
BTRFS critical (device dm-2 state E): emergency shutdown
BTRFS error (device dm-2 state E): error while writing out transaction: -30
BTRFS warning (device dm-2 state E): Skipping commit of aborted transaction.
BTRFS error (device dm-2 state EA): Transaction 9 aborted (error -30)
BTRFS: error (device dm-2 state EA) in cleanup_transaction:2068: errno=-30 Readonly filesystem
BTRFS info (device dm-2 state EA): forced readonly
BTRFS info (device dm-2 state EA): last unmount of filesystem 4fbf2e15-f941-49a0-bc7c-716315d2777c
------------[ cut here ]------------
WARNING: disk-io.c:3311 at invalidate_and_check_btree_folios+0xfd/0x1ca [btrfs], CPU#8: umount/914368
CPU: 8 UID: 0 PID: 914368 Comm: umount Tainted: G OE 7.1.0-rc1-custom+ #372 PREEMPT(full) 2de38db8d1deae71fde295430a0ff3ab98ccf596
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 02/02/2022
RIP: 0010:invalidate_and_check_btree_folios+0xfd/0x1ca [btrfs]
Call Trace:
<TASK>
close_ctree+0x52e/0x574 [btrfs d2f0b1cd330d1287e7a9919d112eadfc0e914efd]
generic_shutdown_super+0x89/0x1a0
kill_anon_super+0x16/0x40
btrfs_kill_super+0x16/0x20 [btrfs d2f0b1cd330d1287e7a9919d112eadfc0e914efd]
deactivate_locked_super+0x2d/0xb0
cleanup_mnt+0xdc/0x140
task_work_run+0x5a/0xa0
exit_to_user_mode_loop+0x123/0x4b0
do_syscall_64+0x243/0x7c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
---[ end trace 0000000000000000 ]---
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30539776 owner 9 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30621696 owner 257 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30638080 owner 258 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30654464 owner 7 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30703616 owner 2 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30720000 owner 10 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30736384 owner 4 gen 9 refs 2 flags 0x7
BTRFS warning (device dm-2 state EA): unable to release extent buffer 30752768 owner 11 gen 9 refs 2 flags 0x7
I'm using a stripped down version, which seems to trigger the warning
more reliably:
_fsstress_pid=""
workload()
{
dmesg -C
mkfs.btrfs -f -K $dev > /dev/null
echo 1 > /sys/kernel/debug/clear_warn_once
mount $dev $mnt
$fsstress -w -n 1024 -p 4 -d $mnt &
_fsstress_pid=$!
sleep 0
$godown $mnt
pkill --echo -PIPE fsstress > /dev/null
wait $_fsstress_pid
unset _fsstress_pid
umount $mnt
if dmesg | grep -q "WARNING"; then
fail
fi
}
for (( i = 0; i < $runtime; i++ )); do
echo "=== $i/$runtime ==="
workload
done
[CAUSE]
Inside btrfs_write_and_wait_transaction(), we first try to write all
dirty ebs, then wait for them to finish.
After that we call btrfs_extent_io_tree_release() to free all
extent states from dirty_pages io tree.
However if we hit an error from btrfs_write_marked_extent(), then we
still call btrfs_extent_io_tree_release() to clear that dirty_pages io
tree, which may contain dirty records that we haven't yet submitted.
Furthermore, the later transaction cleanup path will utilize that
dirty_pages io tree to properly cleanup those dirty ebs, but since it's
already empty, no dirty ebs are properly cleaned up, thus will later
trigger the warnings inside invalidate_btree_folios().
---truncated--- |
| Apache Kafka Connect has the /connector-plugins/{connector-type}/config/validate endpoint on its REST API to validate connector configurations.
Apache Kafka Connect also support Configuration Providers which enable to hide the values of sensitive configuration and only resolve them at runtime.
An attacker with access to the validate endpoint can use it to resolve and return plaintext values via any of the configuration providers installed on a Connect worker.
Users are recommended to upgrade to version 4.2.2, 4.3.2, 4.4.0 or above, which fix this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: Recover HW before retire hung submit
During recovery, it is not safe to retire the hung submit before we
recover the GPU. Retiring the submit triggers BO free and that can
result in GPU pagefaults since the GPU may be actively accessing those
BOs.
To fix this, retire the submits after gpu recovery is complete in
recover_worker().
Patchwork: https://patchwork.freedesktop.org/patch/730655/ |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix xmit_frame/xmit_buf leaks on mgnt-frame error paths
issue_beacon(), issue_probersp() and issue_asocrsp() obtain a management
xmit_frame together with its xmit_buf from the driver's fixed-size
management-TX pools via alloc_mgtxmitframe(). On the normal path the frame
is handed to dump_mgntframe(), which transfers ownership and eventually
returns both objects to their pools (the frame and, for beacons, the buf
in rtl8723bs_mgnt_xmit(); other bufs via the pending-xmitbuf/TX-completion
path).
Several error/edge paths return early after a successful
alloc_mgtxmitframe() but before dump_mgntframe(), so ownership is never
transferred and neither object is freed:
- issue_beacon(): beacon larger than 512 bytes
- issue_probersp(): cur_network->ie_length > MAX_IE_SZ
- issue_probersp(): kzalloc() of the SSID scratch buffer fails
- issue_asocrsp(): pkt_type is neither ASSOCRSP nor REASSOCRSP
Because alloc_mgtxmitframe() removes the frame and buf from their free
lists (list_del_init) without placing them on any pending list, an
orphaned pair is on no list and referenced by nobody, so it is only
reclaimed at driver teardown. Repeated hits progressively exhaust the
management-TX pools until alloc_mgtxmitframe() returns NULL and the
interface can no longer send beacons or probe/assoc responses.
Free the frame and buffer on these paths, matching the existing correct
error handling in issue_assocreq(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: nexthop: Increase weight to u16
In CLOS networks, as link failures occur at various points in the network,
ECMP weights of the involved nodes are adjusted to compensate. With high
fan-out of the involved nodes, and overall high number of nodes,
a (non-)ECMP weight ratio that we would like to configure does not fit into
8 bits. Instead of, say, 255:254, we might like to configure something like
1000:999. For these deployments, the 8-bit weight may not be enough.
To that end, in this patch increase the next hop weight from u8 to u16.
Increasing the width of an integral type can be tricky, because while the
code still compiles, the types may not check out anymore, and numerical
errors come up. To prevent this, the conversion was done in two steps.
First the type was changed from u8 to a single-member structure, which
invalidated all uses of the field. This allowed going through them one by
one and audit for type correctness. Then the structure was replaced with a
vanilla u16 again. This should ensure that no place was missed.
The UAPI for configuring nexthop group members is that an attribute
NHA_GROUP carries an array of struct nexthop_grp entries:
struct nexthop_grp {
__u32 id; /* nexthop id - must exist */
__u8 weight; /* weight of this nexthop */
__u8 resvd1;
__u16 resvd2;
};
The field resvd1 is currently validated and required to be zero. We can
lift this requirement and carry high-order bits of the weight in the
reserved field:
struct nexthop_grp {
__u32 id; /* nexthop id - must exist */
__u8 weight; /* weight of this nexthop */
__u8 weight_high;
__u16 resvd2;
};
Keeping the fields split this way was chosen in case an existing userspace
makes assumptions about the width of the weight field, and to sidestep any
endianness issues.
The weight field is currently encoded as the weight value minus one,
because weight of 0 is invalid. This same trick is impossible for the new
weight_high field, because zero must mean actual zero. With this in place:
- Old userspace is guaranteed to carry weight_high of 0, therefore
configuring 8-bit weights as appropriate. When dumping nexthops with
16-bit weight, it would only show the lower 8 bits. But configuring such
nexthops implies existence of userspace aware of the extension in the
first place.
- New userspace talking to an old kernel will work as long as it only
attempts to configure 8-bit weights, where the high-order bits are zero.
Old kernel will bounce attempts at configuring >8-bit weights.
Renaming reserved fields as they are allocated for some purpose is commonly
done in Linux. Whoever touches a reserved field is doing so at their own
risk. nexthop_grp::resvd1 in particular is currently used by at least
strace, however they carry an own copy of UAPI headers, and the conversion
should be trivial. A helper is provided for decoding the weight out of the
two fields. Forcing a conversion seems preferable to bending backwards and
introducing anonymous unions or whatever. |
| When libcurl uses libssh2 with a hashed `known_hosts` file, an unrelated
initial entry can cause host key validation to report a key *mismatch* as a
*missing* key to the `CURLOPT_SSH_KEYFUNCTION` callback. |
| Enabling `CURLOPT_CRLF` causes curl to advertise the raw input byte count in
the `IMAP APPEND {N}` literal while transmitting line-ending expanded data.
The server reads only $N$ bytes for the payload, causing the remaining
overflow bytes to be interpreted and executed as pipelined IMAP commands
within the authenticated session. |
